Vetus DEUTZ DT44 Скачать руководство пользователя страница 34

Страница: 34 / 88

11 Battery, battery connections

Keep battery clean and dry.

Remove battery cables (negative first).

Clean battery posts (+ and -) and clamps

and grease with acid-free and acid-resist-

ant grease.

Ensure that clamps make good contact

after reassembling. Hand tighten the bolts

only.

12 Checking specific gravity

Every Vetus Maintenance-free battery has

a hydrometer (1) built into the cover.

Visual inspection of the hydrometer will

show one of three conditions:

13 Hydrometer operation

• Green dot visible - State of charge

65 % or more.

• Dark - State of charge less than 65 %.

Recharge immediately.

• Clear or light yellow - Electrolyte level

low.

In case of low level, caused by over-

charging the battery for a long period of

time with a voltage too high, replace

battery. Check alternator and/or voltage

regulator.

4 Maintenance

Battery, cables and connections

Every 125 operating hours.

VD00117

VD00118

VD00121

VD00122

VD00123

Vetus maintenance-free batteries

GREEN DOT ALL DARK

CLEAR

Содержание DEUTZ DT44
























































































Результаты поиска

Содержание DEUTZ DT44

Отзывы:

Похожие инструкции для DEUTZ DT44

Бренды по названию

Популярные бренды

Vetus DEUTZ DT44, Руководство по эксплуатации

Результаты поиска

Содержание DEUTZ DT44

Отзывы:

Похожие инструкции для DEUTZ DT44

Бренды по названию

Популярные бренды