VESPA LXV 50 Скачать руководство пользователя страница 98

Страница: 98 / 162

* Supplied with the tool

Specific tooling

020021Y

Front suspension service tool

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

- Use the tool fitted with part 20* and part 21* on

its stem as shown in the figure.

- Push the two roller casings with the handgrip until

their bottoms make contact with the pin end.

- Use the specific tool, fitted with part 1*, and op-

erate the handgrip until the pin and the Nadella are

simultaneously ejected in the direction opposite

the tool thrusting force.

- To eject the second Nadella, use the tool fitted

with part 2* instead of part 1, on the side opposite

the one shown in the figure.

* Supplied with the tool

Specific tooling

020021Y

Front suspension service tool

-The front suspension service operation is useful to replace the connecting parts between the steering

tube and the swinging hub of the front wheel holder, provided that the steering tube and the wheel holder

hub are in excellent conditions.

Suspensions

Vespa LXV 50

SUSP - 98

Содержание LXV 50



































































































































































Результаты поиска

Содержание LXV 50

Отзывы:

Бренды по названию

Популярные бренды

VESPA LXV 50, Руководство по обслуживанию станции

Результаты поиска

Содержание LXV 50

Отзывы:

Бренды по названию

Популярные бренды