VESPA 2008 S 50 4T 4V Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 199

background image

- Voltage supplied at 2000 rpm must be about 25

÷ 35V.

If no value is obtained even with this test, replace

the regulator because it is obviously failing.

N.B.

TO MEASURE THE ABOVE VOLTAGE USE AN ANALOGUE
TESTER THAT CAN MEASURE ALTERNATING VOLTAG-
ES AND KEEP THE ENGINE AT IDLE TO HAVE AN ALTER-
NATING VOLTAGE OF A FREQUENCY AS CLOSE AS
POSSIBLE TO 50HZ SO AS TO DETECT THE EFFICIENT
VOLTAGE VALUE SUPPLIED BY THE REGULATOR
(ABOUT 12V).

Recharge system voltage check

3) BATTERY NOT RECHARGING

A failure in the direct current section of the voltage

regulator may cause the following problems de-

pending on the type of fault:

a) Protection fuse blows due to overvoltage

(regulator in short circuit) and consequently

the battery fails to recharge.

b) Battery fails to recharge (regulator interrup-

ted).

Measures

a) Protection fuse blows (regulator in short circuit).

Check that the cable harness going from the pro-

tection fuse to the key switch is not damaged,

which may cause a short circuit to ground (thus

preventing damaging the regulator).

Afterwards measure the resistance between con-

tact 3 (Orange) and contact 2 (Black) of the voltage

regulator (with connector disconnected)

If the value measured is far from that indicated,

replace the regulator because it is in short circuit.

b) Battery fails to recharge (regulator interrupted).

To check if there is any failure in the voltage reg-

ulator recharge section, first connect 2 testers to

the battery (one to detect voltage and the other to

detect current) as indicated in the second figure

and follow the procedure below:

Vespa S 50 4T 4V (2008)

Electrical system

ELE SYS - 57

«
...
55
56
57
58
59
...
»

Содержание 2008 S 50 4T 4V








































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 S 50 4T 4V

Бренд: Rascal Страницы: 28

Бренд: E-TRAVELLER Страницы: 32

Rob Family F360

Бренд: Hercules Страницы: 101

Бренд: Xiaomi Страницы: 6

Бренд: PEUGEOT Страницы: 52

Бренд: Baotian Страницы: 100

Бренд: Roma Medical Страницы: 20

Бренд: Robstep Страницы: 71

Бренд: SOLOWAY Страницы: 41

Бренд: EZee Life Страницы: 12

Бренд: EZee Life Страницы: 26

Бренд: G-Force Страницы: 20

emotion easy go

Бренд: BH Страницы: 18

SCOOTER BIG ONE /S

Бренд: HUGO BIKE Страницы: 40

Бренд: MIB Страницы: 18

Бренд: TNG Страницы: 65

Бренд: TNG Страницы: 69

Бренд: Macwheel Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды