VESPA 2008 S 50 4T 4V Скачать руководство пользователя страница 55

Страница: 55 / 199

- Pick-Up

Disconnect the ECU connector and connect the

positive terminal to connector No. 3 (green) and

the negative terminal to connector No. 4 (black).

Use the start-up system to run the engine and

measure the voltage produced by the Pick-Up.

Replace Pick-Up if non-conforming values are

measured.

N.B.

THE MULTIMETER MUST BE SELECTED TO DETECT
CONTINUOUS VOLTAGE.

Electric characteristic

Pick-Up voltage value

Pick-Up voltage value: > 2 Volt

- H.V. coil

With the electronic starter and the HV coil connec-

ted to the system, measure the voltage of the coil

primary during the start-up test with the voltage

peak adaptor and by connecting the positive ter-

minal to the ground lead and the negative terminal

to the coil positive connector.

If non-conforming values are measured, replace

the control unit.

THE POSITIVE TERMINAL OF THE HV COIL PRIMARY IS
BLACK.

Electric characteristic

High voltage coil voltage value

High voltage coil voltage value: > 100 Volt

Stator check

- Using a tester, check the resistance between the

brown-earth and black-earth terminal.

N.B.

VALUES ARE STATED AT AMBIENT TEMPERATURE. A
CHECK WITH THE STATOR AT OPERATING TEMPERA-
TURE LEADS TO VALUES HIGHER THAN THOSE STATED.

Electric characteristic

Stator : Brown-earth

approx. 170

Ω

(Pick-Up)

Stator : Black-earth

Vespa S 50 4T 4V (2008)

Electrical system

ELE SYS - 55

Содержание 2008 S 50 4T 4V








































































































































































































Результаты поиска

Содержание 2008 S 50 4T 4V

Отзывы:

Похожие инструкции для 2008 S 50 4T 4V

Бренды по названию

Популярные бренды

VESPA 2008 S 50 4T 4V, Руководство пользователя

Результаты поиска

Содержание 2008 S 50 4T 4V

Отзывы:

Похожие инструкции для 2008 S 50 4T 4V

Бренды по названию

Популярные бренды