VESPA 2008 S 50 4T 4V Скачать руководство пользователя страница 109

Страница: 109 / 199

- Measure distance between rotors (inner rotor/

outer rotor) with a thickness gauge in the position

shown in the picture.

Characteristic

Admissible maximum clearance 1

0.15 mm

Measure the distance between the outer rotor and

the pump body (see figure).

Characteristic

Admissible maximum clearance 2

0.20 mm

- Check the axial clearance of the rotors using a

trued bar as reference as shown in the figure.

N.B.

MAKE SURE THE TRUED BAR IS POSITIONED PROPERLY
ON THE TWO POINTS ON THE PUMP BODY.

Characteristic

Admissible maximum clearance 3

0.09 mm

Refitting

- Check there are no signs of wear on the oil pump

shaft or body.

- Check there are no signs of scoring or wear on

the oil pump cover.

- If you detect non-conforming measurements or

scoring, replace the faulty parts or the assembly.

- Fit the cover on the pump being careful to align

the holes (2 on the cover and 2 on the pump body)

fixing the oil pump on the crankcase.

- Fit the oil pump on the crankcase by tightening

the two screws to the prescribed torque.

Vespa S 50 4T 4V (2008)

Engine

ENG - 109

Содержание 2008 S 50 4T 4V








































































































































































































Результаты поиска

Содержание 2008 S 50 4T 4V

Отзывы:

Похожие инструкции для 2008 S 50 4T 4V

Бренды по названию

Популярные бренды

VESPA 2008 S 50 4T 4V, Руководство пользователя

Результаты поиска

Содержание 2008 S 50 4T 4V

Отзывы:

Похожие инструкции для 2008 S 50 4T 4V

Бренды по названию

Популярные бренды