VESPA 2008 S 50 4T 4V Скачать руководство пользователя страница 56

Страница: 56 / 199

~ 1

Ω

(Stator)

Voltage regulator check

A malfunction in the voltage regulator might cause the following problems depending on the type of

fault:

1) Bulbs burned out (regulator in short circuit).

2) Malfunction of the lighting system and the electric starter (regulator interrupted).

3) Battery not recharging.

4) Turn indicators not working.

The regulator is earthed through the electrical system, so the regulator body does not earth the circuits

inside the regulator.

There must be insulation between each regulator terminal and the regulator body (use the tester to

check electric resistance).

2) LIGHTS AND STARTER NOT WORKING

Gain access to the voltage regulator by removing

the plastic cover on the legshield; start the engine

and keep running it at idle speed.

Connect the tester positive probe to terminal No.

1 (yellow cable) and the negative probe to terminal

No. 2 (black cable); check if there is voltage.

If there is voltage, check that the light remote con-

trol and its excitation line, coming from the elec-

tronic starter (sky blue PIN 7 - purple PIN 3) work

properly. Check the cable harness from the light

switch to the remote control and whether the

switch works properly .

If no voltage is detected, try connecting the nega-

tive probe directly to earth; if voltage is detected

with this operation, check the earth wiring of the

regulator; otherwise, replace the regulator be-

cause it is failing.

As a last check, the voltage supplied by the stator

can be measured:

- Disconnect the regulator connector and place a

tester to detect alternating voltage between the

Blue cable (4) and the ground connection (see fig-

ure).

Electrical system

Vespa S 50 4T 4V (2008)

ELE SYS - 56

Содержание 2008 S 50 4T 4V








































































































































































































Результаты поиска

Содержание 2008 S 50 4T 4V

Отзывы:

Похожие инструкции для 2008 S 50 4T 4V

Бренды по названию

Популярные бренды

VESPA 2008 S 50 4T 4V, Руководство пользователя

Результаты поиска

Содержание 2008 S 50 4T 4V

Отзывы:

Похожие инструкции для 2008 S 50 4T 4V

Бренды по названию

Популярные бренды