VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 124

background image

VESDA-E VES-A00-P Product Guide

www.xtralis.com

57

5.5.2

VESDAnet Options

The VESDAnet options provide the ability to control network data transmission behaviour for VESDAnet
connections.

Note:

Refer to Section 5.6 for the default settings.

Figure 5-13: VESDAnet Communications Options

The Communications configuration options are as follows:

l

Preferred Port:

The preferred VESDAnet port to be used to transmit network data from this device. The

non-preferred port is used if for some reason transmissions on the preferred port fail. For best
performance in large networks, this setting should be randomly distributed between connected devices.

l

Loop Open Ended on This Device:

This should be checked if the network has been wired so either

VESDAnet port A or VESDAnet B is not connected on this detector. (Xtralis recommends that
VESDAnet ports A and B are always connected so this option should normally not be checked.).

l

Minimum interval between status events:

The minimum time interval between status updates for the

selected detector.

«
...
61
62
63
64
65
...
»

Содержание VESDA-E VES-A00-P





























































































































Отзывы:

Нет отзывов

Похожие инструкции для VESDA-E VES-A00-P

Бренд: tepro Страницы: 32

Бренд: BALANCE TIME Страницы: 2

Бренд: Nemaxx Страницы: 47

Бренд: La Crosse Technology Страницы: 20

Бренд: Salora Страницы: 12

Бренд: AEG Страницы: 28

Бренд: AEG Страницы: 48

Бренд: AEG Страницы: 46

SRC 4331 CD/MP3

Бренд: AEG Страницы: 64

Бренд: AEG Страницы: 122

Бренд: Philips Страницы: 20

Бренд: Philips Страницы: 3

Бренд: Prestige Страницы: 6

Бренд: Datexx Страницы: 1

Бренд: Datexx Страницы: 1

Бренд: iHome Страницы: 16

Бренд: iHome Страницы: 20

Бренд: Vision Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды