VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 66

Страница: 66 / 124

VESDA-E VES-A00-P Product Guide

www.xtralis.com

Static IP Address Configuration

IP Address:

IPV4 static address

Subnet Mask:

Subnet mask for static address

Default Gateway:

Gateway for static address

5.5.5

Security Options

The Security options page allows you to define the number of WiFi/Ethernet connections and the USB, WiFi
and Ethernet connection idle timeouts.

Figure 5-16: Security Options

Maximum number of WiFi/Ethernet connections:

The number of connections which can be running

at any time (WiFi and considered Ethernet together.)

USB Connection Idle Timeout (minutes):

The USB connection will be dropped after no activity from

the user on Xtralis VSC for this period of time.

Ethernet/WiFi connection idle timeout (hours):

Ethernet and WiFi connections will be dropped after

no activity from the user on Xtralis VSC on the particular connection for this period of time. The user can
also choose the option of no timeout.

Содержание VESDA-E VES-A00-P





























































































































Результаты поиска

Содержание VESDA-E VES-A00-P

Отзывы:

VESDA VESDA-E VES-A00-P, Руководство по эксплуатации продукта, Страница: 66 / 124

Результаты поиска

Содержание VESDA-E VES-A00-P

Отзывы: