VESDA VESDA-E VES-A00-P Скачать руководство пользователя страница 16

Страница: 16 / 124

VESDA-E VES-A00-P Product Guide

www.xtralis.com

Specification

Value

Sensitivity Range

0.005 to 20% obs/m (0.0016 to 6.25% obs/ft.)

Threshold Setting Range

Alert:

0.005%–2.0% obs/m

(0.0016% - 0.625% obs/ft)

Action:

0.005%–2.0% obs/m

(0.0016% - 0.625% obs/ft)

Fire1:

0.010 %–2.0% obs/m

(0.0031% - 0.625% obs/ft)

Fire2:

0.020 %–20.0% obs/m

(0.0063% - 6.25% obs/ft)

Notes:

UL and ULC:

For open area, open area high velocity and

duct protection the fire alarm threshold (setting) that
initiates an evacuation signal must be set such that the
sensitivity of each sampling hole is more sensitive than
10%/m (3.2%/ft) as determined by the ASPIRE software.

Refer to Section 5.6 on page 71 for the default settings.

Referencing

Reference smoke level source.

Table 2-2: VES-A00-P Detector Specifications (continued...)

Table 2-3: Key Software Features

Event Log

Up to 20,000 events stored on FIFO basis

AutoLearn

Minimum 15 minutes

Maximum 15 days, 23 hrs, 59 minutes

Recommended 14 days

Thresholds are automatically changed from the previously set
values to the updated values after the AutoLearn process has
completed.

Referencing

Adjustment for external ambient conditions

Four Alarm Levels

Alert, Action, Fire1 and Fire2

Two Fault Warning Levels

Maintenance and Major Fault

Maintenance Aids

Filter and flow monitoring

Event reporting via VESDAnet and event log

Table 2-4: Ordering Information

VESDA-E VES-A00-P Detector

VES-A00-P

Exhaust Adaptor US

VSP-961

Note:

Refer to Table 7-2 for the spare parts list.

Содержание VESDA-E VES-A00-P





























































































































Результаты поиска

Содержание VESDA-E VES-A00-P

Отзывы:

Похожие инструкции для VESDA-E VES-A00-P

Бренды по названию

Популярные бренды

VESDA VESDA-E VES-A00-P, Руководство по эксплуатации продукта

Результаты поиска

Содержание VESDA-E VES-A00-P

Отзывы:

Похожие инструкции для VESDA-E VES-A00-P

Бренды по названию

Популярные бренды