Vertiv Liebert PPC Скачать руководство пользователя | Manualshive

Страница: 5 / 52

background image

Vertiv

|

Liebert

®

PPC

™

User Manual | Rev. 6 | 03/18 |

1

IMPORTANT SAFETY INSTRUCTIONS

Read this entire manual before installing or operating the system.

ELECTROMAGNETIC COMPATIBILITY

—The Liebert PPC complies with the limits for a Class A digital device,

pursuant to Part 15 of FCC rules.

Operation is subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received, including interference that may cause undesired operation.

Operating this device in a residential area is likely to cause harmful interference that users must correct at their
own expense.

The Liebert PPC complies with the requirements of EMC Directive 2014/30/EU and the published technical
standards. Continued compliance requires installation in accordance with these instructions and use of
accessories approved by Vertiv.

WARNING

Risk of cutting bands under tension. Can cause injury or death.
The shipping bands may be under tension. Use appropriate eye, face and hand protection to safeguard
against injury from band backlash.

WARNING

Risk of electric shock. Can cause injury or death.
Verify that all incoming line voltage (power) and low-voltage (control) circuits are de-energized and
locked out before installing cables or making connections, whether in the junction box or in the unit.
Equipment inspection and startup should be performed only by trained personnel. Lethal voltages are
present during startup procedures. Electrical safety precautions must be followed throughout inspection
and startup.
Only properly trained and qualified service personnel should perform maintenance on the Liebert PPC. All
voltage sources to the unit must be disconnected before inspecting or cleaning within the cabinet.
Lethal voltages exist within the equipment during operation. Observe all warnings and cautions in this
manual. Failure to comply may result in serious injury or death. Obtain qualified service for this equipment
as instructed.
The monitoring system contains a lithium battery for memory backup. Danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent type. Dispose of used batteries according to
manufacturer’s instructions.

WARNING

Risk of electric shock. Can cause injury or death.
All power and control wiring should be installed by licensed electricians and must comply with the NEC
and applicable codes.

WARNING

Risk of improper handling. Can cause equipment damage, injury or death.
The Liebert PPC is heavy; its weight ranges from 400lb. (182kg) to 2450lb. (1111kg) The unit should not
be loosened from the shipping pallet until after all handling by forklift or pallet jack is completed

«
...
3
4
5
6
7
...
»

Содержание Liebert PPC





















































Отзывы:

Нет отзывов

Похожие инструкции для Liebert PPC

Бренд: Pacific Power Source Страницы: 114

Бренд: Steelcase Страницы: 4

Бренд: Milwaukee Страницы: 8

Бренд: GE Digital Energy Страницы: 644

POWER360 P360-DOCK

Бренд: Panamax Страницы: 8

Server Technology PRO3X

Бренд: LEGRAND Страницы: 182

Бренд: ABB Страницы: 2

Бренд: BEGA Страницы: 2

Бренд: Ametek Страницы: 90

Бренд: Ametek Страницы: 114

Бренд: Regin Страницы: 3

Бренд: PHENYX PRO Страницы: 12

Бренд: Microsemi Страницы: 17

Heathkit HP-1144 Guide

Бренд: Heathkit Страницы: 33

Бренд: environmental potentials Страницы: 7

Бренд: Delta-Opti Страницы: 4

Бренд: CleanSweep Страницы: 4

Бренд: Avocent Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды