Vertex Standard EVX-S24 Скачать руководство пользователя

Страница: 11 / 44

EVX-S24 O

PERATING

ANUAL

EFORE

EGIN

Battery Pack Removal

1. Turn the radio off and remove any protective cases.
2. Slide the Battery Cover Latch into the “

UNLOCK

”

side, then remove the Battery Cover.

3. Pinch the top side of the Battery Pack, then pull out

the Battery Pack.

Battery Pack Installation

1. Make sure that the

VOL/PWR

knob powered off, by

turning the knob counter clockwise to a complete stop.

2. Slide the Battery Cover Latch into the “

UNLOCK

”

position, then remove the Battery Cover.

3. Install the

FNB-V142LI

Battery Pack into the battery

compartment of the transceiver.

4. Re-attach the battery cover by aligning the tabs of the

battery cover with the slots on the transceiver and slid-
ing into position.

5. Slide the Battery Cover Latch into the “

LOCK

” posi-

tion.







CAUTION



Risk of explosion if battery is replaced by an

incorrect type. Dispose of used batteries ac-
cording to the instructions.



Do not attempt to open any of the recharge-

able Lithium-Ion packs, as they could ex-
plode if accidentally short-circuited.

Use the Vertex Standard
FNB-V142LI Lithium-Ion
Battery Pack only.











Содержание EVX-S24













































Результаты поиска

Содержание EVX-S24

Отзывы:

Похожие инструкции для EVX-S24

Бренды по названию

Популярные бренды

Vertex Standard EVX-S24, Руководство по эксплуатации

Результаты поиска

Содержание EVX-S24

Отзывы:

Похожие инструкции для EVX-S24

Бренды по названию

Популярные бренды