background image

 

  www.versitron.com 

 

 
 

1.3 SPECIFICATIONS 
 
Data Rate

:  Any data rate from 250 Bps to 10.0 Mbps, synchronous; 100 Kbps, asynchronous. 

 
Operating Mode

:

  

Simplex, Half or Full duplex operation over fiber optic cable pair. 

 
Optical Interface

:

 

ST connectors. 

 
Digital Interface

:

   

Signal levels and format conform to EIA RS-530 (synchronous and 

asynchronous) and MIL-STD 188-114 Balanced and Unbalanced. 
 

Electrical Interface

:  Female DB25 (DCE) connector. 

 
Bit Error Rate

:  Better than 10

-9

 
MTBF

:  96,428 hrs. 

 

Dimensions

:

  

7 x 1 x 11 in. WxHxL (17.8 x 2.5 x 27.9 cm). 

 
Weight

:

  

12.0 oz. (0.34 kg). 

 

Power Requirements

:

   

12 VDC @ 1.5A, 18 watts; optional VAC to VDC wall transformer: 

(VERSITRON Model PSAC15, 120 VAC ~ 60 Hz to 12 VDC, 1.5A) 
(VERSITRON Model PSAC09, 230 VAC ~ 50 Hz to 12 VDC, 1A) 
 

Environment

:

   

0° to +50° C (32° to +122° F) operating temperature; up to 95% relative 

humidity (non-condensing); up to 10,000 feet altitude; storage temperature -40° to +70° C. 
 

Model 

F2238 F2240 F2245 

Connector 

ST ST ST 

Wavelength 

850 nm 

Multimode 

1300 nm 

Multimode 

1300 nm 

Single Mode 

Link Budget* 

18 

±

 1 dB 

16 

±

 1 dB 

22 

±

 1 dB 

Maximum 

Range* 

2 Km 

(1.24 mi./6,560 ft) 

6 Km 

(3.7 mi./19,680 ft) 

15 Km 

(9.3 mi./49,100 ft) 

Fiber Cables 

50 or 62.5/125 µM 

100/140 µM 

62.5/125 µM 

8 or 9 or 10/125 µM 

*

Note

:  Multimode tests were performed on 62.5/125 

μ

M fiber optic cable. 

 

Single Mode tests were performed on 9/125 

μ

M fiber optic cable. 

Содержание F2238
















Отзывы: