VersaLogic Blackbird VL-EPU4462 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 74

background image

Mass Storage Interfaces

VL-EPU-4562/4462 Reference Manual

31

Mass Storage Interfaces

SATA Interface

The Blackbird provides three serial ATA 3.0 (SATA 3.0) ports that communicate at a rate of up

to 6.0 Gbits/s. Two ports connect to right-angle SATA connectors with latching capability. The

third port connects to Minicard #1 when an mSATA module is installed.
The ATX power supplies Power to the SATA drive. Note that the standard SATA drive power

connector is different from the common 4-pin Molex connector used on IDE drives. Most current

ATX power supplies provide SATA connectors, and many SATA drives provide both types of

power connectors. If the power supply you are using does not provide SATA connectors,

adapters are available.

Figure 12. Location of the SATA Connectors

4

«
...
29
30
31
32
33
...
»

Содержание Blackbird VL-EPU4462











































































Отзывы:

Нет отзывов

Похожие инструкции для Blackbird VL-EPU4462

Бренд: Acer Страницы: 106

Бренд: Acer Страницы: 83

Бренд: Acer Страницы: 81

Бренд: Acer Страницы: 89

T230H - Bmidh Wide Touch Screen Display

Бренд: Acer Страницы: 12

Бренд: Acer Страницы: 100

Бренд: IBM Страницы: 18

Бренд: IBM Страницы: 152

PowerMate 2000 Series

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 8

DIRECTION L - SERVICE

Бренд: NEC Страницы: 139

Бренд: Chen Hsong Страницы: 124

Бренд: Predator Страницы: 98

Бренд: M5Stack Страницы: 15

Бренд: MicroTouch Страницы: 52

Rosemount TankRadar SCC 5320

Бренд: Emerson Страницы: 4

Бренд: Emerson Страницы: 108

Бренд: IEI Technology Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды