background image

11

1

Fig. 1.11

=

=

Dotted  line  showing  the  position 

of the range when installed

17” 

15/16

(455.5 mm)

Anti-tip stability

device

Adjustable

bracket with

threaded nut

correctly fitted

Anti-tip stability

device fixing

3. 

Fix the stability bracket in place. It can be 

fixed as follows:

• 

To  the  floor  OR  on  the  rear  wall  by  #4 

screws (supplied).

• 

To  the  floor  AND  on  the  rear  wall  by  #8 

screws (supplied).

• 

There  are  8  x  wood  screws  and  8  x 

screws with plastic

 

sleeve anchors supplied with the range 

in two separate kits.

 

Use  the  proper  screws  according  to 

the  type  of  material  on  the  floor  and/

or wall.

• 

If using the the plastic sleeve anchors: drill 

5/16” (8mm) diameter holes and insert the 

supplied plastic sleeve anchors before 

attaching  the  stability  bracket  with  the 

screws.

4. 

Slide the range into place, ensuring the bolt 

on  the  adjustable  bracket  slots  under  the 

stability bracket.

• 

Adjust the length of the bolt as necessary. 

Ensure the two nuts are well tightened after 

any adjustments.

IMPORTANT!

• 

Use the proper screws to fix the stability 

bracket in place

 

according to the type of material on the 

floor and/or wall.

• 

Before drilling and holes or inserting any 

screws into the

 

floor  or  wall  check  that  you  will  not 

damage any wiring or

 

pipes.

WARNING 

- Slide range back so bolt head, on the adjustable bracket assembly, is 

--

under anti-tip bracket.

 

- Look for the anti-tip bracket securely attached to floor or wall.

 

- See installation instructions for details.

 

- Look for the adjustable bracket assembly securely attached to 

--

the back of the range.

 

- Slide range forward.

To verify the anti-tip bracket is installed and engaged:

Tip-Over Hazard

  

Anti-tip bracket

Adjustable bracket 

assembly to be fixed to 

the back of  the range

 

A child or adult can tip the range and be killed.

Install anti-tip device to range and/or structure per installation 

instructions.

Engage the range to the anti-tip device Installed to the structure.

Re-engage anti-tip device if range is moved.

Failure to follow these instructions can result in death or serious 

burns to children and adults

.

Содержание VDFSEE365 Series

















Отзывы: