Vermont Castings Signature Series VCS325SSBI Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 14

Vermont Castings Signature Series VCS325SSBI Series Скачать руководство пользователя страница 6

6

30007230

VCS325SSBI/525SSBI Series Assembly

NOTE:

Ensure your grill enclosure has been constructed according to the exact specifi cations shown in Figure 2. If the en-

closure is constructed of wood or other similar combustible materials, the use of the insulated jacket Model VCS301SSIJ
or VCS501SSIJ is required.

If you have an LP model with a 20lb cylinder stored in the enclosure, ensure there are at least two (2) air ventilation
openings of 10 sq. inches (64.5 cm2) 180 degrees apart and they are level with the cylinder valve. Another two (2)
openings with the same dimensions and distance are required to be level with the base of the cylinder. An enclosure for
an LP gas cylinder shall be ventilated by openings at both the upper and lower levels of the enclosure. The effectiveness
of the opening(s) for purposes of ventilation shall be determined with the LP gas supply cylinder in place. This shall be
accompanied by one of the following:

a. One side of the enclosure shall be completely open; or

b. For a cylinder enclosure having four (4) sides, a top and a bottom and intended for installation in a built-in enclosure:

1. At least one (1) ventilation opening shall be provided on the exposed exterior side of the enclosure located within

5 in. (127 mm) of the top of the enclosure and unobstructed. The opening(s) shall have a total free area of not less
than 1 in

2

/lb (14.2 cm

2

/kg) of stored fuel capacity.

2. At least one ventilation opening shall be provide don the exposed, exterior side of the enclosure 1 in (25.4 mm)

or less from the fl oor level and shall have a total free area of not less than 1/2 in

2

/lb (7.1 cm

/kg) of stored fuel

capacity. The upper edge shall be no more than 5 in (127 mm) above the fl oor level.

3. Every opening shall have a minimum dimension so as to permit the entrance of a 1/8 in (3.2 mm) rod.

Always confi rm the installation of this grill conforms with the requirements of all local codes or, in the absence of any
applicable local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or CSA B149.1, Natural Gas and
Propane Installation Code.

«
...
4
5
6
7
8
...
»

Содержание Signature Series VCS325SSBI Series















Отзывы:

Нет отзывов