Vermont Castings Signature Series VCS325SSBI Series Скачать руководство пользователя страница 5

5

30007230

VCS325SSBI/525SSBI Series Assembly

VCS325SSBI / VCS525SSBI Framing Dimensions

When Using Combustible Materials

(ZC Insulated Jacket Required for Installation)

A

D

E

F

B

P

C

H

M

G

W

W

W

 

Ref. VCS325SSBI 

VCS525SSBI

 A 

33

5

16

" (846 

mm) 

45

5

16

" (1153 

mm)

 B 

24

5

8

" (626 

mm) 

24

5

8

" (626 

mm)

 C 

11

1

8

" (283 

mm) 

11

1

8

" (283 

mm)

 D 

3

1

16

" (78 

mm) 

3

1

16

" (78 

mm)

 

3" 

(76 mm) 

3" 

(76 mm)

 

2" 

(51 mm) 

2" 

(51 mm)

 

3" 

(76 mm) 

3" 

(76 mm)

 H* 

18

3

4

" (476 

mm) 

18

3

4

" (476 

mm)

 I 

28

3

4

(730 mm) 

38" 

(965 mm)

 J 

12

5

8

" (321 

mm) 

12

5

8

" (321 

mm)

 K 

18

1

4

" (464 

mm) 

18

1

4

" (464 

mm)

 

10" 

(254 mm) 

10" 

(254 mm)

 M 

3

1

2

(89 mm) Min. 

3

1

2

(89 mm) Min.

 

4" 

(102 mm) Min. 

4" 

(102 mm) Min.

 

4" 

(102 mm) Min. 

4" 

(102 mm) Min.

 P 

2

1

2

(64 mm) Min. 

2

1

2

(64 mm) Min.

 S 

9

7

8

" (250 

mm) 

13

13

16

" (350 

mm)

 

3"  

(76 mm) 

3" 

(76 mm)

 

4" 

(102 mm) 

4" 

(102 mm)

 V 

5

15

16

" (150 

mm) 

5

15

16

" (150 

mm)

 

W** 

36" 

(914 mm) 

36" 

(914 mm)

Drain Holes
(2" diameter)

Drain Holes
(2" diameter)

B333a

*Applies if optional side burner Model VCSSBIB will be installed.

**** Clearance from grill lid/hood to combustible materials.

NOTE:

 If the optional side sear burner Model VCSSBIE will be installed, refer to installation instructions suppied with burner kit for 

framing dimensions.

NOTE:

 If the grill is installed directly under a combustible overhang or ceiling, the ceiling must be at least 38" (965 mm) above the 

countertop.

Содержание Signature Series VCS325SSBI Series















Отзывы: