background image

35

Dutchwest Direct Vent / Natural Vent Gas Heater

30001935 

LIMITED LIFETIME WARRANTY 

PRODUCT COVERED BY THIS WARRANTY
All Dutchwest gas stoves equipped with an Insta-Flame Ceramic Burner.

BASIC WARRANTY

CFM Corporation Company (hereinafter referred to collectively as the 
Company) warrants that your new Dutchwest Gas Fireplace/Stove is 
free from manufacturing and material defects for a period of one year 
from the date of purchase, subject to the following conditions and 
limitations.

EXTENDED LIFETIME WARRANTY

The heat exchanger, where applicable, and combustion chamber of 
every Dutchwest gas product is warranted for life against through 
wall perforation. All appliances equipped with an Insta-Flame Ce-
ramic Burner have limited lifetime coverage on the ceramic burner 
plaque. Warrantees are made to the original owner subject to proof 
of purchase and the conditions and limitations listed on this Warranty 
Document

COMPONENT WARRANTY

CAST IRON: All external and internal cast iron parts are warranted for a 
period of three years.

Note:

 On porcelain enamel finished external parts and accessories 

The Company offers no Warranty on chipping of enamel surfaces. 
Inspect all product prior to accepting it for any damage to the enamel.
The salt air environment of coastal areas or a high humidity environ-
ment can be corrosive to the porcelain enamel finish. These condi-
tions can cause rusting of the cast iron beneath the porcelain enamel 
finish, which will cause the finish to flake off.
Dye lot variations with replacement parts and/or accessories can oc-
cur and are not covered by warranty.

GLASS DOORS: Glass doors are covered for a period of one year. 
Glass doors are not warranted for breakage due to misuse or accident.  
Glass doors are not covered for discoloration or burned in stains due to 
environmental issues, or improper cleaning and maintenance.
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be 
cleaned with Lemon oil only. Brass cleaners cannot be used.  Mortar 
mix and masonry cleaners may corrode the brass finish.  The Company 
will not be responsible for, nor will it warrant any brass parts which are 
damaged by external chemicals or down draft conditions.
GAS VALVES: Gas valves are covered for a period of one year
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and 
mechanical components of the burner assembly are covered for one 
year. All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM 
Corporation company supplied accessories are covered for a period of 
one year.

CONDITIONS AND LIMITATIONS

•  This new Dutchwest product must be installed by a competent, 

authorized, service contractor. A licensed technician, as prescribed 
by the local jurisdiction must perform any installation/service work. 
It must be installed and operated at all times in accordance with the 
Installation and Operating instructions furnished with the product. 
Any alteration, willful abuse, accident, or misuse of the product shall 
nullify this warranty.

•  This warranty is non-transferable, and is made to the original owner, 

provided that the purchase was made through an authorized supplier 
of the Company.

•  The customer must pay for any Authorized Dealer in-home travel 

fees or service charges for in-home repair work. It is the dealers op-
tion whether the repair work will be done in the customer’s home or in 
the dealer’s shop.

•  If upon inspection, the damage is found to be the fault of the manu-

facturer, repairs will be authorized at no charge to the customer parts 
and/or labor.  

•  Any part and/or component replaced under the provisions of this 

warranty is covered for six months or the remainder of the original 
warranty, whichever is longest.

•  This warranty is limited to the repair of or replacement of part(s) 

found to be defective in material or workmanship, provided that such 
part(s) have been subjected to normal conditions of use and service, 
after said defect is confirmed by the Company’s inspection.

•  The company may, at its discretion, fully discharge all obligations 

with respect to this warranty by refunding the wholesale price of the 
defective part(s)

•  Any installation, labor, construction, transportation, or other related 

costs/expenses arising from defective part(s), repair, replacement, or 
otherwise of same, will not be covered by this warranty, nor shall the 
Company assume responsibility for same. Further, the Company will 
not be responsible for any incidental, indirect, or consequential dam-
ages except as provided by law.

• 

SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR LIMI-
TATIONS OF INCIDENTAL AND CONSEQUENTIAL DAMAGES OR 
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, 
SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR CIR-
CUMSTANCES.  THIS WARRANTY GIVES YOU SPECIFIC RIGHTS 
AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM 
STATE TO STATE. 

•  All other warranties-expressed or implied- with respect to the product, 

its components and accessories, or any obligations/liabilities on the 
part of the Company are hereby expressly excluded.

•  The Company neither assumes, nor authorizes any third party to as-

sume on its behalf, any other liabilities with respect to the sale of this 
CFM Corporation product

•  The warranties as outlined within this document do not apply to chim-

ney components or other non CFM Corporation accessories used in 
conjunction with the installation of this product..

•  Damage to the unit while in transit is not covered by this warranty but 

is subject to claim against the common carrier. Contact the dealer 
from whom you purchased your fireplace/stove (do not operate the 
appliance as this might negate the ability to process the claim with 
the carrier).

•  The Company will not be responsible for:
  a)  Down drafts or spillage caused by environmental conditions such 

as near-by trees, buildings, roof tops, hills, or mountains.

  b)  Inadequate ventilation or negative air pressure caused by me-

chanical systems such as furnaces, fans, clothes dryers, etc.

•  This warranty is void if:
  a)  The fireplace has been operated in atmospheres contaminated by 

chlorine, fluorine, or other damaging chemicals.

  b)  The fireplace has been subjected to prolonged periods of damp-

ness or condensation

  c)  Any damages to the fireplace, combustion chamber, heat 

exchanger or other components due to water, or weather damage, 
which is the result of but not limited to, improper chimney/venting 
installation.

  d)  Any alteration, willful abuse, accident, or misuse of the product 

has occurred.

IF WARRANTY SERVICE IS NEEDED…

1) Contact your supplier.  Make sure you have your warranty, your 

sales receipt, and the model/serial number of your  CFM Corpo-
ration product.

2) DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.

Содержание Dutchwest 2465





































Отзывы: