Vermont Castings DBT33 Скачать руководство пользователя

Страница: 23 / 34

10002789/0

-23-

DBT33/DBT36/DBT39

LIGHTING INSTRUCTIONS

3. Open control access panel.

4. Push in gas control knob slightly and turn clock-

wise to "OFF". Do not force.

5. Close control access panel.

10. Push the control knob all the way in and hold.

Immediately light the pilot by repeatedly depress-

ing the piezo spark ignitor until a ame appears.

Continue to hold the control knob in for about one

(1) minute after the pilot is lit. Release knob and it

will pop back up. Pilot should remain lit. If it goes

out, repeat steps 5 through 8.

• If knob does not pop up when released, stop

and immediately call your service technician or gas

supplier.

• If after several tries, the pilot will not stay lit, turn

the gas control knob to "OFF" and call your service

technician or gas supplier.

11. Replace glass door.

12. Turn gas control knob to "ON" position.

13. For RN/RP appliances turn the On/Off switch to

"ON" position or set thermostat to desired setting.

14. Turn on all electrical power to the replace.

1. STOP! Read the safety information above on this

page.

2. Turn off all electrical power to the replace.

3. For MN/MP/TN/TP appliances ONLY, go on to

Step 4. For RN/RP appliances turn the On/Off

switch to “OFF” position or set thermostat to lowest

level.

4. Open control access panel.

5. Push in gas control knob slightly and turn clockwise

to "OFF". Do not force.

6. Wait ve (5) minutes to clear out any gas. Then

smell for gas, including near the oor. If you smell

gas, STOP! Follow "B" in the safety information

above on this page. If you don't smell gas, go to

the next step.

7. Remove glass door before lighting pilot. (See Glass

Frame Removal in manual).

8. Visibly locate pilot by the main burner.

9. Turn knob on gas control counter clockwise

to "PILOT".

neighbour's phone. Follow the gas supplier's

instructions.

•If you cannot reach your gas supplier, call the

Fire Department

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will not

push in or turn by hand, do not try to repair it, call a

qualied service technician. Applying force or any

attempted repair may result in a re or explosion.

D. Do not use this replace if any part has been under

water. Immediately call a qualied service techni-

cian to inspect the replace and to replace any part

of the control system and any gas control which has

been under water.

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING:

If you do not follow these instructions exactly, a re or explosion may

result causing property damage, personal injury or loss of life.

A. This replace has a pilot which must be lit manu-

ally.

When lighting the pilot follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the re-

place area for gas. Be sure to smell next to the

oor because some gas is heavier than air and will

settle on the oor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any replace.

•Do not touch any electric switch

•Do not use any phone in your building

•Immediately call your gas supplier from a

TO TURN OFF GAS TO FIREPLACE

LIGHTING AND OPERATING INSTRUCTIONS

1. Turn the On/Off switch to “OFF” position or set

the thermostat to lowest setting.

2. Turn off all electric power to the replace if

service is to be performed.

EURO SIT

SIT NOVA

HONEYWELL

OFF

PILOT

OFF

3/8" - 1/2"

Содержание DBT33



































Результаты поиска

Содержание DBT33

Отзывы:

Похожие инструкции для DBT33

Бренды по названию

Популярные бренды

Vermont Castings DBT33, Инструкции по установке и Руководство для владельца дома

Результаты поиска

Содержание DBT33

Отзывы:

Похожие инструкции для DBT33

Бренды по названию

Популярные бренды