manualshive.com logo in svg
background image

ZL0119-0F 

Page 31 of 34 

©2019 Veris Industries   USA 800.354.8556 or +1.503.598.4564  / [email protected] 0119 

 

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of  Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

TM

E50F2A, E50F5A Installation Guide

Configuration Properties (cont.)

CP Name

Type

NV Num.

R/W

Applies To

Range

Default Value

Description

cpPhaseLossImbal

UCPTphLossImbal 
(UCP_Type_10 w/o 

resource files)

(SNVT_count ref.)

19

R/W

“Meter” Function 

Block

1 - 99 (%)

25(%)

Phase Loss Imbalance Threshold in percent. For 

a 3-phase Y(3+N) system (type 40), both Line 

to Neutral and Line to Line voltages are tested. 

In a 3-phase delta system (type 31), only the 

Line to Line voltages are examined. In a single 

split-phase (2+N) system (type 12), just the 

Line to Neutral voltages are compared.

cpDemSubintLen

UCPTDemSubintLen 
(UCP_Type_11 

w/o resource files) 

(SNVT_count ref.)

20

R/W

“Meter” Function 

Block

0, 10 - 32767 

(seconds)

900 (seconds)

Sub-Interval Length in seconds. For sync-to-

comms, set this to 0 and use nviDemSubintRes 

to externally restart the sub-interval.

cpDemSubintCnt

UCPTDemSubintCnt
(UCP_Type_1 w/o 

resource files) 

(SNVT_count ref.)

21

R/W

“Meter” Function 

Block

1 - 6

1

Number of Sub-Intervals per Demand Interval. 

Sets the number of sub-intervals that make 

a single demand interval. For block demand, 

set this to 1. 

PROPAGATION CONTROL
cpMaxNvSntPerSec UCPTnvUpdtLimit 

(UCP_Type_2 w/o 

resource files) 

(SNVT_count)

29

R/W

“Meter” Function 

Block

0 - 65535

10

Limits the total number of updates sent out per 

second for network variables in the following 

categories: Energy, Power, Voltage, Current, 

Power Factor, Frequency, Pulse Counters, 

Startup Count, and Alerts. If more than the 

number of updates specified is queued to be 

sent out in any 1 second period, the excess 

updates are delayed until the next second 

to reduce network traffic. This configuration 

property is provided to give rough burst 

control. The number of packets sent per 

second will vary based on the connection 

types (ACK, UNACK, etc.) and updates from 

other network variables that are not controlled 

by this configuration property.

cpAllEnergy

SCPTminSndT

1

R/W

All energy output 

network variables

0 - 1 hour, 

49 minutes, 

13 seconds, 

500ms (6553.5 

seconds)

15 seconds

Throttle for all energy output network variables. 

After propagation of a network variable, 

updates to the same network variable are 

blocked for the time set by this configuration 

property. The configuration property is shared, 

but each energy output network variable has 

its own independent throttle counter that 

resets to the value specified by this CP after it 

has been propagated.

cpAllPower

SCPTminSndT

2

R/W

All power output 

network variables

0 - 1 hour, 

49 minutes, 

13 seconds, 

500ms (6553.5 

seconds)

15 seconds

Throttle for all power output network variables. 

After propagation of a network variable, 

updates to the same network variable are 

blocked for the time set by this configuration 

property. The configuration property is shared, 

but each power output network variable has 

its own independent throttle counter that 

resets to the value specified by this CP after it 

has been propagated.

cpAllVoltage

SCPTminSndT

3

R/W

All voltage output 

network variables

0 - 1 hour, 

49 minutes, 

13 seconds, 

500ms (6553.5 

seconds)

15 seconds

Throttle for all voltage output network 

variables. After propagation of a network 

variable, updates to the same network 

variable are blocked for the time set by this 

configuration property. The configuration 

property is shared, but each voltage output 

network variable has its own independent 

throttle counter that resets to the value 

specified by this CP after it has been 

propagated.

Содержание E50F2A



































Отзывы: