manualshive.com logo in svg
background image

ZL0124-0E 

Page 19 of 20 

©2018 Veris Industries   USA 800.354.8556 or +1.503.598.4564  / [email protected] 0818 

 

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of  Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

TM

E50C1A Installation Guide

E50C1 REG.

R/W NV Format

Units

Scale

Range

Description

152

R/W NV UInt

0-32767

Power Up Counter. 

153

R

NV UInt

0-32767

Output Configuration. E50C1 always returns 0

154

R

UInt

Reserved, returns 0

Floating Point Data

257/258 R

NV Float

kWh

Real Energy Consumption (clear via reset register)

259/260 R

NV Float

kWh

Real Energy Consumption (clear via reset register)

261/262 R

Float

kW

Total Instantaneous Real Power

Invalid or Quiet Not A Number (QNAN) conditions are indicated by 0x8000 (negative zero) for 16 bit integers and 0x7FC00000 for 32 bit floating point numbers.

Floating point numbers are encoded per the IEEE 754 32-bit specifications.

Modbus Point Map (cont.)

Содержание E50C1A





















Отзывы: