Verex ISM/xL, Руководство по оборудованию

Страница: 58 / 66

54 Monitor ISM/xL™ Hardware Guide
22-0375 rev1.1
Module Power Supply
red
Normally Open
Common
Normally Closed
0V
12
TB1
12
TB2
3
12
4
3
12
4
TB5
3
12
TB6
AC Mains
AC Mains
Earth GND
Earth GND
Auxiliary (+)12VDC
0V
Auxiliary (+)12VDC
0V
(+)12V
(
-
) 0V
Data B
Data A
bla
ck
yello
w
gre
en
Module
Bus
(SNAPP)
VBUS
12
TB7
0V
Tamper Input
TB
3
TB4
T
rou
bl
e
Ou
tp
ut
(
-
)
(+)
Battery Connectors
1.
0
AM
P
Out
put
(+) (
-
)
P8
P7
P6
P5
P4
P9
P10
Manual Battery
Re-start
Battery
reset-able
fuse
Auxiliary power
reset-able fuse
Cover
Tamper
Spring
Module Power
Supply
Anti-Attack Bushing Cap (p/n 364-5102) covers the rear tamper spring. It fits inside an “ O “
Ring Bushing (p/n 364-5103) that fits inside the metal cabinet’s rear wall, anti-tamper spring,
knock-out. Leave the O ring bushing and cap IN if the rear tamper is not used. If the rear
tamper is used, remove the cap and the O ring with the edge of a flat screw driver. Discard the
O ring. Align the cap to insert in the tamper spring, knock-out hole on the control cabinet back.
Screw the cap by its center hole to the mounting surface. Place the control cabinet over it,
allowing the rear tamper spring to fit inside the cap. The cap will insert in the metal cabinet’s
tamper spring, knock-out hole. Complete securing the metal cabinet to the mounting surface.
Rear Tamper on
back of board.
Momentarily jumper
after a battery has been
connected and there is
no AC mains available.
5 digit serial number
to program in Module
Programming
XXXXX
This unjumpered
connector not used.
Do not jumper.
These unjumpered
connectors not used.
Do not jumper.
Factory set.
Do not adjust.
1 2
SNAPP
Isolate
Battery
Plug
3
12
(+)12V
SNAPP ISOLATE: Jumper/short with wire to enable Module Bus (SNAPP) connector 12VDC.
Battery Cable p/n 166-2645
Not used
P3 jumper in = rear
tamper bypassed
1
1
2
2
Brownout Button: After installation and all power connections are complete, press this button
to establish a frame of reference to detect a brownout.
Button
Wire short
for cover
tamper
spring
operation
only.
AC Mains On
Green LED
Additional Cover
Po
we
r O
n
Gr
ee
n L
E
D
Tro
ubl
e
Ye
llo
w L
E
D
Modu
le
B
u
s
c
o
m
m
u
n
ica
ti
on
s R
e
d
LED
Processor
OK Green
LED
Slow flash.
Fast flash
with no
VBUS
connected.
Ratings:
North American:
Input: 16.5VAC/40VA/50-
60Hz/60W, 50mA
Output: 12VDC
Europe:
Input: 230VAC/50Hz, 50mA
Output: 12VDC
Temp for both: -10°C to
+55°C (14°F to 131°F) @
93%
Refer to Installation Instructions P/N 21-3614 for further information.