Ventrac LX423 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 49

Ventrac LX423 Скачать руководство пользователя страница 20

SERVICE

Service - 20

3. Remove the two bolts (B) from the bracket that

holds the rear blower shaft bearing.

4. Rotate the bracket (C) as shown to allow the fan

drive belt to be removed.

5.

C

Remove the PTO drive belt.

6. Remove the old fan drive belt and install the new

belt onto the pulleys.

7. Reinstall the PTO drive belt.

8. Rotate the bracket back into place and install the

two bolts.

9. Engage the fan drive belt tensioning spring.
10. Reinstall the gearbox/fan belt cover.

Auger Drive Belt Replacement

1. Remove the auger drive belt cover.

2.

Spring may be under high tension. Use caution

when releasing spring, as pinching may occur.

Release the auger belt tension spring.

3. Remove the old auger drive belts and install the

new drive belts onto the pulleys.

4. Engage the auger belt tensioning spring.

5. Reinstall the auger drive belt cover.

Belt Tension Adjustment

The belt spring tension is adjustable. The belt tension

is factory set with the least amount of tension. This

allows some belt slippage to protect the gearbox and

drive components in the event an immovable object

stops the auger or fan. If excessive belt slippage

occurs in normal operating conditions, belt tension

may be increased by moving the spring arm to a dif-

ferent notch on the belt tightener plate or to a different

bolt for the auger drive belt tensioning spring.

Lubrication Locations

Lubrication is required at the following locations using

a lithium complex NLGI #2 grease. Refer to the main-

tenance schedule for service intervals. Use only one

pump of grease.

Auger Shaft Bearings

Fan Shaft Bearings

Discharge Chute Rotation Chain

Gearbox

The gearbox uses 80-90 weight gear oil. Gearbox oil

level should be maintained at approximately half full.

Refer to maintenance schedule for service intervals.

«
...
18
19
20
21
22
...
»

Содержание LX423


















































Отзывы:

Нет отзывов