manualshive.com logo in svg

Ventrac LX423, Руководство оператора, Страница: 19 / 49

Поделиться
Скачать
Ventrac LX423 Скачать руководство пользователя страница 19

SERVICE

Service - 19

Cleaning & General Maintenance

For best results, and to maintain the finish of the 

LX423, clean or wash the snow blower to remove 

dirt, gravel, and salt deposits. Remove any ice or 

snow accumulations from the auger, fan, fan hous-

ing, and discharge chute. 

            Attention

To maintain the finish of the power unit and attach

-

ment, thoroughly wash the equipment after each 

use to remove any corrosive agents (e.g., salt). Fail-

ure to clean the equipment may result in corrosion 

of (including but not limited to) steel, aluminum, and 

electrical components. Equipment that will experi-

ence repeated exposure to corrosive agents should 

be pretreated with a corrosion preventative.

Cutting Edge Reversal/Replacement

If the cutting edge wears down near the snow blower 

frame structure, remove the cutting edge and flip over 

so the unworn top edge is now on the bottom. Rein-

stall the cutting edge onto the snow blower. When 

both sides of the cutting edge have been worn down, 

the cutting edge will need to be replaced.

Skid Shoe Replacement

Skid shoes should be replaced when wear surface is 

less than 1/8” thick.

Belt Inspection/Replacement

Inspecting the drive belts of 

the snow blower can prevent 

sudden belt failure by finding 

problems before they cause a 

belt to break. Typical wear on 

a drive belt may result in the 

conditions shown in the 

diagram. If any of these 

conditions occur, the drive belt 

will require replacement.

 

 

Belt Size

 

Venture Part # 

 

PTO Drive Belt  

A90 

81.A090 

(power unit to snow blower)

Auger Drive Belt 

A48 

81.A048

Fan Drive Belt 

B63 

81.B063

Fan Drive Belt Replacement

1. 

 

Always set the parking brake, shut off power 

unit engine, remove the ignition key, and ensure 

all moving parts have come to a complete stop 

before inspecting components, or attempting 

any repair or adjustment.

Remove the gearbox/fan belt cover from the 

snow blower.

2. 

 

Spring may be under high tension. Use caution 

when releasing spring, as pinching may occur.

Release the fan drive belt tensioning spring (A).

A

B

B

C

SERVICE

Always set the parking brake, shut off power 

unit engine, remove the ignition key, and ensure 

all moving parts have come to a complete stop 

before inspecting components or attempting any 

repair or adjustment.

            Attention

If any component requires replacement, use only 

original Ventrac replacement parts.

Содержание LX423


















































Отзывы:

Нет отзывов