VENGEANCE Invader 2003 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 80

background image

V E N G E A N C E M O T O R C Y C L E S O W N E R S M A N U A L

- 67 -

Vengeance Motorcycles, Mira Loma, CA USA • 866-483-6432 • www.VengeanceMotorcycles.com

© 2003 Vengeance Performance Products, LLC All Rights Reserved • VOM 1st Edition Rev 2.3 06/03

500-MILE MAINTENANCE

Change engine oil and oil filter and clean tappet screen.

Change transmission lubricant and clean magnetic drain plug.

Inspect air cleaner and service as required.

Check and adjust primary belt.

Check and adjust drive belt with motorcycle loaded (rider and any additional normal load).

Check and adjust shift rod.

Check and adjust clutch.

Inspect brake pads and discs for wear.

Inspect oil lines and brake system for leaks.

Check brake fluid reservoir levels and condition. Add fluid as needed.

Check and adjust front brake lever.

Check and adjust rear brake pedal.

Inspect and lubricate both forward control lever bearings.

Lubricate front brake hand lever, throttle control cables, throttle, clutch control cable, & clutch hand lever.

Check and adjust fuel enrichener operation.

Inspect fuel valve, lines, and fittings for leaks.

Check and adjust front and rear tire pressures and inspect tread and sidewall condition.

Check rear fork pivot nut, if applicable.

Check operation of all electrical equipment and switches.

Clean battery connections.

Inspect spark plugs and replace as needed (replacement at an additional charge).

Check shock absorbers.

Check stabilizer links and engine mounts.

Check tightness of all fasteners except engine head bolts.

Check and adjust engine idle speed.

Perform diagnostic test on ignition module, note readings for discussion with customer.

Confirm operation and performance with road test

Complete form above, attach copy of ignition diagnostic report, and forward to:

Vengeance Motorcycles Warranty Dept. 4501 Etiwanda Avenue Mira Loma, CA 91752 Fax (909) 681-2901

(Maintain a copy of this form for your records.)

NOTE:

The 500-mile maintenance service is MANDATORY and must be performed by an authorized Vengeance

Motorcycles Dealer or Service Center to keep your warranty in effect

500-MILE MAINTENANCE SERVICE

DATE COMPLETED:__________ DEALER:______________________________
CUSTOMER:_______________________________________________________
MODEL:______________ YEAR:____________ MILEAGE:_________________
TECHNICIAN:______________________________________________________
TECH COMMENTS:_________________________________________________

__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________

ٱ

Copy of ignition diagnostic report attached

«
...
65
66
67
68
69
...
»

Содержание Invader 2003

















































































Отзывы:

Нет отзывов

Похожие инструкции для Invader 2003

Бренд: MRA Страницы: 9

Бренд: Sena Страницы: 25

TorqDrive Clutch Pack

Бренд: Rekluse Страницы: 18

Бренд: Yamaha Страницы: 248

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 53

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 126

XMAX CZD300M 2021

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 215

Бренд: Yamaha Страницы: 259

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды