VENGEANCE Invader 2003 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 80

background image

V E N G E A N C E M O T O R C Y C L E S O W N E R S M A N U A L

- 55 -

Vengeance Motorcycles, Mira Loma, CA USA • 866-483-6432 • www.VengeanceMotorcycles.com

© 2003 Vengeance Performance Products, LLC All Rights Reserved • VOM 1st Edition Rev 2.3 06/03

FASTENERS

Check for loose or missing nuts, bolts or cotter pins. If you keep the motorcycle clean, it is easier to spot missing
parts. Refer to Specification for recommended fastener torque (tightness).

SPARK PLUGS / IGNITION SYSTEM

Spark plugs should be inspected and the gap measured (and adjusted if required) at every recommended inspection
and maintenance interval. Spark plugs should be replaced at a minimum of every 12,000 miles (more frequently for
optimal performance.)

When replacing your motorcycle’s spark plugs:

•

Always replace with same as original equipment plugs.

•

Never remove spark plug wires from plugs by pulling on wires. Always grasp the molded rubber spark plug

cap for removal of wires.

Vengeance Motorcycles installs one of the most advanced, electronic ignition systems presently available on the
market. Only a professionally trained mechanic should address its sophisticated electronic operation. As set at the
factory, your ignition system optimizes fuel consumption, engine horsepower and exhaust emissions. It should not be
adjusted except by a professional motorcycle mechanic familiar with its operation and functions utilizing the
appropriate equipment.

SUSPENSION

Adjustment:

Although the spring pre-load or ride height of the motorcycle can be adjusted to compensate for

variations in weight, it is not recommended as an owner process.

CAUTION: ALTHOUGH THE SUSPENSION HEIGHT CAN BE ADJUSTED, IT IS SET FOR NORMAL OPERATION
AND LOAD FROM THE FACTORY. ANY VARIANCE FROM THIS SETTING SHOULD BE CONFIRMED PRIOR TO
PERFORMING THE PROCESS. IT IS RECOMMENDED THAT ANY ADJUSTMENTS MADE TO YOUR
SUSPENSION BE PERFORMED BY AN AUTHORIZED VENGEANCE MOTORCYCLES DEALER OR SERVICE
CENTER.

WARNING

LOWERED MOTORCYCLES HAVE REDUCED CORNERING CLEARANCE AND REDUCED REAR
WHEEL TRAVEL. EXTRA CARE MUST BE TAKEN WHEN CORNERING ON A LOWER MOTORCYCLE.
ALSO, ALTERING RIDE HEIGHT AFFECTS THE STEERING GEOMETRY AND CAN LEAD TO A
POTENTIALLY HAZARDOUS CONDITION.

WARNING

YOUR NEW HIGH PERFORMANCE MOTORCYCLE IS SUBJECT TO VIBRATION DURING USE UNDER
ALL OPERATING CONDITIONS. BOLTS, FASTENERS, CABLES AND FIXTURES SUCH AS LIGHTS
ETC. SHOULD BE INSPECTED FREQUENTLY AND TIGHTENED OR REPLACED, IF NECESSARY, TO
ENSURE THE SAFE AND DEPENDABLE OPERATION OF THE VEHICLE. CERTAIN MODELS, SUCH AS
THOSE BUILT ON RIGID FRAMES, ARE SUBJECT TO GREATER VIBRATION, AND FASTENERS AND
FIXTURES MUST BE CHECKED EVEN MORE FREQUENTLY TO ENSURE SAFETY AND PROPER
OPERATION.

«
...
53
54
55
56
57
...
»

Содержание Invader 2003

















































































Отзывы:

Нет отзывов

Похожие инструкции для Invader 2003

Бренд: hepco & becker Страницы: 2

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

Бренд: KYMCO Страницы: 55

Бренд: hepco & becker Страницы: 4

Бренд: PUIG Страницы: 6

Бренд: Abus Страницы: 18

Бренд: Dayi Motor Страницы: 18

Бренд: Palm Страницы: 14

Бренд: Saddlemen Страницы: 2

Бренд: Saddlemen Страницы: 2

Бренд: Saddlemen Страницы: 4

Бренд: Saddlemen Страницы: 4

Бренд: Cagiva Страницы: 157

2003 Planet 125

Бренд: Cagiva Страницы: 156

2007 raptor 125-E 3

Бренд: Cagiva Страницы: 156

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 61

DragStar XVS650A

Бренд: Yamaha Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды