VENGEANCE Invader 2003 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 80

background image

V E N G E A N C E M O T O R C Y C L E S O W N E R S M A N U A L

- 36 -

Vengeance Motorcycles, Mira Loma, CA USA • 866-483-6432 • www.VengeanceMotorcycles.com

© 2003 Vengeance Performance Products, LLC All Rights Reserved • VOM 1st Edition Rev 2.3 06/03

Function Switch

The function switch is used for calibration and to read out the odometer mileage. Pressing and holding the function
switch while the gauge is running will display the odometer mileage as follows:

“odo” > thousands > hundreds > tenths

65,432.1 would be displayed as follows: “odo” > “ 65” > “432” > “ .1”

Pressing and releasing the function switch while the gauge is running will display the trip mileage
as follows:

“trP” > hundreds > tenths

123.4 would be displayed as follows: “trP” > “123” > “ .4”

The trip mileage will continue to be displayed until the functions switch is momentarily pressed
again. Pressing and holding the function switch while the trip mileage is being displayed will reset it to
zero.

TURN SIGNAL INDICATORS

Your motorcycle is equipped with front and rear, left and right side, D.O.T.–approved, self-canceling turn signals.
These turn signals are operated by turn signal switches located on the handlebar controls. The left side turn signal
switch operates both the front and rear left side turn signal lights. The right side turn signal switch operates both the
front and rear right side turn signal lights.

Depressing either turn signal switch will begin the corresponding side turn indicator lights blinking on and off.
Always ensure that turn signal lamps are operating. Replace burned-out lamps only with approved replacements.

Headlamp Hi/Lo Switch

WARNING

NEVER REMOVE FACTORY INSTALLED TURN SIGNALS OR REPLACE WITH NON-D.O.T. APPROVED UNITS.
NON-D.O.T.-APPROVED REPLACEMENT UNITS MAY BE MORE DIFFICULT TO BE SEEN BY OTHER VEHICLE
OPERATORS

«
...
34
35
36
37
38
...
»

Содержание Invader 2003

















































































Отзывы:

Нет отзывов

Похожие инструкции для Invader 2003

Бренд: Idaho Страницы: 72

F 850 GS Adventure 2019

Бренд: BMW Motorrad Страницы: 346

ST400 Cruiser Edition

Бренд: STEEL HORSE AUDIO Страницы: 6

Two Fifty 250 cc

Бренд: Mash Страницы: 62

Бренд: BMW Motorrad Страницы: 231

Бренд: X-lite Страницы: 84

Бренд: Ice Bear Страницы: 64

Sixteenth Edition

Бренд: MSF Страницы: 60

Бренд: DYNATEK Страницы: 12

Бренд: Shark Страницы: 76

Бренд: BMW Страницы: 205

Бренд: MSA Страницы: 168

Бренд: Saddlemen Страницы: 2

Бренд: APRILIA Страницы: 151

Бренд: Benelli Страницы: 51

Бренд: hepco & becker Страницы: 8

Бренд: Honda Страницы: 191

450 Rally Factory Replica 2014

Бренд: KTM Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды