Vega VEGAPULS 56K Скачать руководство пользователя страница 8

Страница: 8 / 72

VEGAPULS 56K

HART

-handheld

HART

-handheld on the 4␣ …␣ 20␣ mA-signal line

VEGAPULS 56 sensors with 4␣ …␣ 20␣ mA-output
signal can also be adjusted with the HART

handheld. A special DDD (Data Device
Description) is not required so that the sensors
can be adjusted with the HART

-standard

menus of the handheld.

For adjustment just connect the HART

handheld in any position of the 4␣ …␣ 20␣ mA-

output signal line or to the sensor connection
terminals.

1.4 Antennas

4 ... 20 mA

HART Communicator

Product description

Adjustment with adjustment module
MINICOM

With the (3,2␣ cm␣ x␣ 6,7␣ cm) 6-key adjustment
module with display you can carry out the
adjustment in clear text. The adjustment mod-
ule can be plugged into the radar sensor or
into the optional external indicating instrument.

By removing the adjustment module unauthor-

ized adjustments are avoided.

Adjustment with HART

-handheld

Detachable adjustment module MINICOM

Adjustment with detachable adjustment module on
the radar sensor or on the external indicating instru-
ment VEGADIS 50

ESC

Tank 1
m (d)
12.345

ESC

Tank 1
m (d)
12.345

4 ... 20 mA

ESC

Tank 1

m (d)
12.345

Содержание VEGAPULS 56K









































































Результаты поиска

Содержание VEGAPULS 56K

Отзывы:

Похожие инструкции для VEGAPULS 56K

Бренды по названию

Популярные бренды

Vega VEGAPULS 56K, Инструкция по эксплуатации

Результаты поиска

Содержание VEGAPULS 56K

Отзывы:

Похожие инструкции для VEGAPULS 56K

Бренды по названию

Популярные бренды