background image

3

1 For your safety

VEGAPULS SR 68 • Modbus and Levelmaster protocol

47164-EN-140129

1  For your safety

1.1  Authorised personnel

All operations described in this operating instructions manual must 

be carried out only by trained specialist personnel authorised by the 

plant operator.
During work on and with the device the required personal protective 

equipment must always be worn.

1.2  Appropriate use

VEGAPULS SR 68 is a sensor for continuous level measurement.

You can find detailed information about the area of application in 

chapter "

Product description

".

Operational reliability is ensured only if the instrument is properly 

used according to the specifications in the operating instructions 

manual as well as possible supplementary instructions.

1.3  Warning about incorrect use

Inappropriate or incorrect use of the instrument can give rise to 

application-specific hazards, e.g. vessel overfill or damage to system 

components through incorrect mounting or adjustment.

1.4  General safety instructions

This is a state-of-the-art instrument complying with all prevailing 

regulations and guidelines. The instrument must only be operated in a 

technically flawless and reliable condition. The operator is responsible 

for the trouble-free operation of the instrument.

During the entire duration of use, the user is obliged to determine the 

compliance of the necessary occupational safety measures with the 

current valid rules and regulations and also take note of new regula-

tions.

The safety instructions in this operating instructions manual, the na

-

tional installation standards as well as the valid safety regulations and 

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device 

beyond that described in the operating instructions manual may be 

carried out only by personnel authorised by the manufacturer. Arbi-

trary conversions or modifications are explicitly forbidden.

The safety approval markings and safety tips on the device must also 

be observed.

Depending on the instrument version, the emitting frequencies are in 

the C or K band range. The low emitting frequencies are far below the 

internationally approved limit values. When used correctly, there is no 

danger to health.

Содержание PULS SR 68





















Отзывы: