Vega C-6124 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 80

background image

37

Vega’s C-

6124

CROSSMUTE ENCODE/DECODE: The C-6124 has an audio Crossmute feature. This feature sends a DTMF digit
before and after each transmission. Parallel consoles decode this DTMF and remove that line’s audio from their
speaker outputs. This feature allows console operators in the same room to operate without a feedback loop
occurring. The programmer may independently enable or disable both the encoding of the DTMF signal and the
decoding o f the DTMF signal. For example, in a room with three consoles in parallel all three will have their
CROSSMUTE ENCODE and DECODE set to ON. The console in the next room, which is tied in parallel, is in no
danger of audio feedback; therefore, both of the CROSSMUTE attributes are set to OFF. Note that this feature uses
DTMF digits “C” and “D”. If it is possible for these digits to be used in the system, disable the tone Crossmute
feature or problems will occur. A hardwire Crossmute is offered through each TLM modular connector as an
alternative.

LAM FLASH: Each TLM has a programmable Line Activity Monitor (LAM) flash setting. This may be programmed
from 0 to 9 seconds. This is the length of time that the LAM light on the front panel will blink after the squelch gates
block the receive audio.

«
...
41
42
43
44
45
...
»

Содержание C-6124

















































































Отзывы:

Нет отзывов

Похожие инструкции для C-6124

Бренд: Valve Concepts Страницы: 16

ESSENSSE NEO COMFORT

Бренд: 2VV Страницы: 21

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: TCS Basys Controls Страницы: 2

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: GCE Страницы: 24

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: Samson Страницы: 48

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды