background image

VEC1087 A

REV101103

9

APPENDIXA - CHARGING TIMES

To calculate the approximate charging time required to fully charge a battery, it is necessary to determine the specific
gravity (or, percent of battery charge) using a hydrometer. Use this technique if battery vent caps can be removed. Check
each cell. A cell with a very low specific gravity compared to the other cells probably means a shorted cell in the battery.
Replace the battery.

The following chart converts hydrometer readings into percent of charge values.

SPECIFIC GRAVITY

PERCENT OF CHARGE

PERCENT OF CHARGE NEEDED

(HYDROMETER READING)

IN BATTERY

BY BATTERY

1.265

100%

0%

1.225

75%

25%

1.190

50%

50%

1.155

25%

75%

1.120

0%

100%

Refer to the chart below for approximate charging times.

PERCENT OF CHARGE

75%

50%

25%

0%

2 AMPS

7 HRS

13 HRS

NR*

NR*

6 AMPS

2.5 HRS

5 HRS

7 HRS

9 HRS

10 AMPS

1.5 HRS

3 HRS

4 HRS

5 HRS

* Not recommended.
The times shown in the chart above are approximate and refer to an average automotive battery. For smaller batteries,
the charge time should be adjusted using the formula shown below and adding 1 hour to the time calculated. To estimate
charging time for a discharged battery, divide the amp hour (AH) rating of the battery by the charge rate selected. This
is the number of hours required to recharge the battery. For example, a 50 Ah (12 volt) battery is discharged (10 volts).
How long should it be charged at the 6 Amp rate? Divide the 50 Ah by 6. 

Answer:

approximately 8 hours. Always round up charge time by 10% to ensure full charge. In most cases, battery charge

times will vary depending on age and condition of battery. Smaller batteries should be charged at the lower rate (2 Amps)
and add an extra hour to charge time.

Содержание VEC1087 A










Отзывы: