background image

25

Does the upper duct pipe need to be positioned in a 
2 degree angle?

No, this can be level but it is no problem to 
mount it under a 2 degree angle, the upper 
duct does not drain any condensate, it only 
guides incoming air.

Can we change the door to swing direction?

Yes. First the electric cable needs to be 
removed.
Then remove the 2 hinge bolds & nuts and 
mount them on the other side. Don’t forget to 
place back the electric cable.

Should we first mount the upper and lower duct on 

the unit and then mount the Unibody on the wall?

Yes, because the connection of the PVC duct 
pipes and the EPP covers needs to be checked 
visually before mounting the fresh-r

®

 in the 

wall.

What should we do with bag C?

This is a spare part kit, store it at the bottom 
of the unit.

After installation

Does the fresh-r

®

 start in the automatic program?

Yes, it always runs in automatic mode, except 
when the fan speed is changed manually. After 
100 minutes it will go back to automatic mode, 
refer to user manual.

How will the fresh-r

®

 determine at what rate the it 

needs to operate?

The higher the CO² level or the RH (relative 

humidity) levels the more it will ventilate, 
refer to user manual.

I feel cold air coming out of the bottom, is that 
correct?

Yes, moving air feels colder then stationary air, 
refer to user manual.

How can I operate the unit?

On the control panel, “A” for automatic. 
You can increase or decrease the fan speed 
manually using the fan buttons. Refer to the 
user manual. Increase or lower fans speed 
via the fan buttons; refer to user manual.

What does the smiley tell me?

They indicate the air quality, refer to user 
manual.

Does the unit measure RH or CO²?

Yes, it measures both, please refer to user 
manual.

What maintenance should be done?

Rinse heat exchanger with cold water every 
6 months, and clean upper and lower duct pipe 
every 2 years, refer to user manual.

The unit makes noise, is that correct?

If the orange or red face icon is lighted it is 
correct. The air quality is not good enough and 
it substantially increases the ventilation rate. If 
the green smiley is on and it makes more noise 
then 30 dB(A) it could be very humid inside, 
especially just after construction. If the green 
smiley is on and the building is not humid but 
the unit makes noise for more then 3 hours in 
a row, contact your supplier. Refer to user 
manual.

How can we reduce the noise?

Wait till the green light face lightens. If this 
takes too long, open a window. Refer to user 
manual.

The fresh-r

®

 suddenly starts to make noise, but no 

air is coming into the room, what happens?

If it is freezing outside, it is in defrost mode 
and it de-freezes the heat exchanger by 
blowing warm air out, so it can again work at 
optimum efficiency. If it is not freezing outside 
and the fresh-r

®

 suddenly starts to make 

noise, contact your supplier. Refer to user 
manual.

Содержание fresh-r everywhere On-The-Wall





































Отзывы: