VAT Series 612 DN 63-250 Скачать руководство пользователя страница 50

Страница: 50 / 76

Installation, Operating & Maintenance Instructions

Series 612 DN 63-250 (I.D. 2.5“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

289857EA

2011-07-13

50/76

Command

Acknowledgement

(within 10ms after reception of command)

Inquiry function

Description

Get [i:70][CR][LF]

[i:70][xxxxxxxxxx][CR][LF]

THROTTLE CYCLE

COUNTER

data length 10 characters
xxxxxxxxxx number of throttle cycles

This function returns the number of throttle cycles. A movement from max. throttle position
to open back to max. throttle position counts as one cycle. Partial movements will be added
up until equivalent movement is achieved.

Get [i:71][CR][LF]

[i:71][xxxxxxxxxx][CR][LF]

ISOLATION CYCLE

COUNTER

data length 10 characters
xxxxxxxxxx number of isolation cycles

This function returns the number of isolation cycles. Each closing of the sealing ring counts
as one cycle.

Get [i:72][CR][LF]

[i:72][xxxxxxxxxx][CR][LF]

POWER UP COUNTER

data length 10 characters
xxxxxxxxxx number of power ups

This function returns the number of control unit power ups.

Get [i:80][CR][LF]

[i:80][abcdefgh][CR][LF]

HARDWARE

CONFIGURATION

data length 8 characters

0 = Power Failure Option (PFO) not equipped

1 = Power Failure Option (PFO) equipped

0 = ±15V sensor power supply (SPS) not equipped

1 = ±15V sensor power supply (SPS) equipped

8 = RS485 Interface without analog outputs

9 = RS485 Interface with analog outputs

1 = 1 sensor version, 2 = 2 sensor version

efgh

reserved, do not use

This function returns the hardware configuration of the device.

Get [i:82][CR][LF]

[i:82][xxxxxxxx][CR][LF]

FIRMWARE

CONFIGURATION

data length 8 characters
xxxxxxxx

firmware version, e.g. 650P1D00

This function returns firmware version of the device.

Get [i:83][CR][LF]

[i:83][xxxxxxxxxxxxxxxxxxxx][CR][LF]

IDENTIFICATION

data length 20 characters
xxx...xxx

identification code, e.g. /0001/, unused digits are filled up with spaces (20
hexadecimal)

This function returns an identification code. This code is unique for each valve and allows
tracing.

Содержание Series 612 DN 63-250













































































Результаты поиска

Содержание Series 612 DN 63-250

Отзывы:

Бренды по названию

Популярные бренды

VAT Series 612 DN 63-250, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Series 612 DN 63-250

Отзывы:

Бренды по названию

Популярные бренды