VariProp DF-160 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 10

background image

Formular-Nr.:71 Rev.-Nr.:07 03/18

-3-

INSTALLATION on the shaft

ATTACHING THE HOUSING CAP with ZINC-ANODE:

First, insert all three housing cap screws

(1,

also page 8

)

loosely, then tighten securely in succession.

Use LOCTITE low (pink) and observe the little washers.

ENGINE DRY TEST:

Please consider that a dry test of the engine

MUST NOT

be done while the VARIPROP is fitted onto

the shaft ! The VARIPROP needs water pressure on the blades, otherwise the prop could be
damaged !!

«
1
2
3
4
5
...
»

Содержание DF-160











Отзывы:

Нет отзывов

Похожие инструкции для DF-160

Бренд: NEC Страницы: 44

Бренд: JB-Lighting Страницы: 60

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: Olsen Страницы: 58

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

CIRCOLINA G10q T9

Бренд: Life Страницы: 2

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Quadra Force/Sys

Бренд: American DJ Страницы: 1

Бренд: Sunrise Medical Страницы: 9

Бренд: Tektronix Страницы: 54

Бренд: obsta Страницы: 37

Бренд: Fillauer Страницы: 12

Бренд: Hoshizaki Страницы: 35

Бренд: lumishore Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды