background image

7

Emergency stop

Only to be used for 

emergency situations 

and for powering off 

the mixer

Timer  [mmss]

Reset the timer by pres

-

sing the two timer but

-

tons at the same time. 
Time is shown in mi-
nutes and seconds. 

Time down

Time up

Power off the mixer

 -

 Push the emergency stop

Power on the mixer 

-

 Turn the emergency stop clockwise

Start/Stop (pause)

To be used when check

-

ing the contents of the 

bowl or otherwise pau

-

sing the mixer

Timer  [mmss]

Reset the timer by pres

-

sing the two timer but

-

tons at the same time. 
Time is shown in mi-
nutes and seconds. 

Time down

Time up

Before the mixer is stopped, move the 

speed selector lever back to the lowest 

speed (fig.4).

Before starting the mixer:

Ingredients can be filled in the bowl at any time before 

the mixer is started.

1.  Place the tool in the bowl.

2.  Place the bowl in the bowl arms.

3.  Fit the rear part of the safety guard.

4. 

Grab the tool and lock it into the bayonet fitting.

5.  Lift the bowl to working position. 

6.  Fit the front part of the safety guard

If desired, set an operating time.

The mixer is now ready to be started.

Start the mixer:

Press 

 

to start the mixer.

Turn the speed selector lever (fig. 4) to the rear until the re

-

quired speed has been obtained, (notice the recommended 
maximum speeds on page 6).

The mixer will run until the time set on the timer runs out or 
the user stops the mixer.

Stop the mixer without resetting the timer (Pause)

If it is needed to ad ingredients or check the content of the 
bowl, the mixer can be paused without resetting the timer.

• 

Press 

 the mixer stops

Safety guard can now be opened and the bowl can be 
lowered.

To start the mixer again, close the safety guard and/or 

lift the bowl. The mixer can now be started by pressing 

 the timer will continue counting down.

Reset the timer:

Reset the timer by pressing the two timer buttons at the 
same time.

Use emergency stop for stopping the mixer:

The emergency stop should only be used in 

emergency situations and for powering off the 

mixer. Not used in normal operation.

If the emergency stop is activated or main power to the 

mixer is cut off, the tool stops rotating and the timer is 

reset to zero.

Timer automatically repeats the previous setting:

When the running time runs out, the tool stops rotating, 
the timer shortly display [0000] and will then display the 
previous selected running time.

More about the timer:

Timer settings of up to 90 minutes

If no running time is selected, the display will show the 
time elapsed since the mixer was started.

Start/Stop (pause)

To be used when check

-

ing the contents of the 

bowl or otherwise pau

-

sing the mixer

Recommended maximum speeds:

Содержание 30007630

















Отзывы: