background image

MVS-1C 

Page 3 

General installation guidelines 

-

 

It  is  recommended  to  install  the  unit  in  a  hallway  to  limit  the  MVS-1C  exposure  to 
noxious gases. 

-

 

In  order  to  avoid  condensation  problems  inside  the  MVS-1C,  it  is  recommended  to 
install the module on an inside wall. If it is not possible, use spacers to have an air 
gap between the wall and the controller. 

-

 

The  MVS-1C  should  be  installed  in  easy-access  location  but  away  from  damaging 
elements (heat, cold, water, direct sunlight…).  

-

 

Do  not  install  the  MVS-1C  near  high-voltage  equipment,  power  supply  or 
transformer.

 

-

 

When  installing the mounting  plates  onto the  back  of the  enclosure, makes sure to 
use a regular screw driver (DO NOT use a drill or electric screw driver) to screw the 
tap screws into the plastic holes.

 

 

Wiring Procedure 

 

1.  Open the MVS-1C controller enclosure. 

2.  Verify the technical specifications to know which wire to use. 

3.  Connect the equipment to the 2 black terminal block identified as FAN as shown 

in figure 1. 

    

4.  Connect  the  power  source  to  the  2  black  terminal  block  identified  as  LINE  as 

shown in figure 1. 

5.  Make  sure  that  the  voltage  selector  switch  is  set  to  the  correct  voltage  before 

powering up the MVS-1C (refer to figure 2 for the location of the switch). 

6.  Power up the MVS-1C controller. Verify that the controller operates correctly. 

7. 

Close the MVS-1C enclosure. Don’t forget to put a security screw or a padlock.

 

 

www.monitrol.com

Содержание MVS-1C











Отзывы: