background image

                                                                                                                   

Page 35  

WARRANTY 

 

Limited Warranty 

 
The manufacturered equipment and supplied 
components have gone through rigorous inspection to 
assure optimal quality of product and reliability. 
Individual controls are factory tested under load, 
however the possibility of equipment failure and/or 
malfunction may still exist. 
 
For service, contact your local retailer or supplier. The 
warranty period shall be for two years from 
manufacturing date. Proof of purchase is required for 
warranty validation. 
 
In all cases, the warranty shall apply only to defects in 
workmanship and specifically exclude any damage 
caused by over-voltage, short circuit, misuse, acts of 
vandalism, fortuitous events, acts of God, flood, fire, 
hail, lightning or any other natural disaster. Any 
unauthorized work, modification or repair on this 
product automatically voids the warranty and 
disclaims the manufacturer from all responsibility. 
 
The manufacturer assumes only those obligations set 
forth herein, excluding all other warranties or 
obligations. This warranty stipulates that in all cases 
the manufacturer shall be liable only for the supply of 
replacement parts or goods and shall not be liable for 
any personal injury, damages, loss of profits, 
interrupted operations, fine contravention of the law or 
damages to the production of the PURCHASER and 
the PURCHASER shall take up the defense and hold 
the manufacturer faultless regarding any legal or 
extra legal proceedings, notice, or claim by the 
customer or by a third party, and regarding any legal 
and extra legal expenses and fees brought forward on 
by such damages. 

www,monitrol.com

Содержание MST-1





































Отзывы: