Vari F-700H, Перевод оригинальной инструкции по эксплуатации, Страница: 8 / 20

F-700H
1.4.1.1 Machine assembly procedure
Use the following procedure when assembling:
1. According to Fig. 2 - after removing the cardboard packaging 1 from the transport pallet 2 , cut the strips 3 fixing the
machine on the pallet and remove the guide wheels 4 . Loosen the tightening nut 5 , straighten the handlebars 6 and tighten
the tightening nut. Press the handlebar lock lever 7 and turn the handlebars 6 to the working position. According to Fig. 3
step > 1 – unscrew the front cover 1 on both sides and remove it from the machine. Move the bypass lever on the gearbox to
the OFF position
(Fig. 14
- 7 ) and carefully drive the machine off the pallet - take extra care.
2. According to
Fig. 3
step > 2 place the front cover 8 on the machine chassis under the deflector and screw it on again –
tighten the screw connection so that the cover can move freely. Install the springs 2 . According to > 3 Press the cutting height
adjustment lever ( 8 in
Fig. 1
), place the frame with the guide wheels 3 and lock the cutting height adjustment ( 26 in
Fig. 1
)
in any position. Screw the frame with the guide wheels to the chassis using screws 4 , flat washers 5 and self-locking nuts 6 .
Finally, according to > 4 , fasten the bowden cables to the handlebar tube (excluding the shifting lever bowden cable) using the
cable ties 7 and cut off the free ends of the cable ties.
1.4.1.2 Handlebars adjustment
The handlebars can be adjusted in two levels
Fig. 4
:
1.
Height:
Loosen the tightening nut 1 and adjust the height of the handlebars to suit you. Tighten the nut.
2. Sides: Press the handlebar lock lever 2 downwards and turn the handlebars left or right one position until the pin locks the
handlebars in the side position.
To reduce the dimensions of the machine, eg when transporting in a car, either fold the handlebars forward over the engine or lower the
handlebars to a horizontal position and then turn the entire handlebars 180 ° clockwise. Be careful not to strain the bowden cables
somewhere on the construction of the machine.
1.4.1.3 Cutting height adjustment
The cutting height setting is affected by several important factors:
●
stand height and density
●
species of predominant plants in the stand
●
travel speed of the machine
●
cutting width
●
surface irregularities
In general, the greater the value of each of these factors, the higher the height of the guide wheels and the height of the blade above
the surface. Always set the cutting height so that the working space of the blade is not clogged. Then the blade speed is reduced, the
engine does not run at optimum speed and the self-cleaning ability of the blade mowing space from accumulated grass material is reduced.

Always increase the cutting height to the highest level before uneven terrain. This will prevent damage to the
knife.
Actual cutting height adjustment using the guide wheels
Fig. 9
:
1. push on both handlebar grips so that the locking pin 2 in the locking plate 3 is relieved.
2. with the fingers of the left hand, press the cutting height adjustment lever 1 on the underside of the left handlebar grip.
3. push the two handles to lower or increase the height of the guide wheels.
4. align one of the oval holes on the locking plate 3 against the locking pin 2
5. release lever 1
1.4.2 Commissioning

The machine may be supplied without engine fluids (depending on various national regulations)!

First, carefully read the engine operating manual 19 ! This will help prevent any engine damage.
1. Check the oil level; if necessary, fill the engine with the recommended type and amount of oil. Fill the tank with the recommended
type and amount of petrol.
2. Move the throttle lever into the 4 CHOKE
20
position. Throttle lever positions 1 = STOP , 2 = MIN , 3 = MAX and 4 = CHOKE
are described in Fig. 5 . All of the four described main positions are locked by a simple crimp-lug in the lever body.
3. Pull the manual starter rope to start the engine 21 .
4. Leave a new or cold engine to run for approx. 30 second with choke on (throttle lever in position 4 ), 4. then move the throttle
lever to the 3 position.

Do not leave the machine unattended!
19
Original engine manual is included in the machine packaging.
20
Engines equipped with automatic choke and throttle lever in MAX position, automatic setting of maximum rpms occurs after the engine has warmed.
21
Directions for starting the engine are described in detail in the engine operating instructions.
8
R
ev
is
io
n
0
1
/2
0
1
6