Van's Aircraft RV-12 страница 4 Скачать руководство пользователя

Страница: 4 / 34

NOTE: Beginning on this page the use of the F-00011 SkyView Template for adding required holes is depicted. If your kit was

supplied with parts already having the holes you are instructed to make using the template, ignore that step and continue.

The F-00011 SkyView Template has many holes. This could become confusing because only a few holes in the template are

used for any given step. Before drilling a set of holes, study the plans carefully and mark the holes to be drilled on the template.

When drilling is complete remove the marks on the template with solvent before moving on to the next drilling operation.

Step 1: Cleco the F-00011 SkyView Template to the two referenced rivet holes in the F-1202B Panel Base as shown in Figure 1.

Step 2: Match-Drill #30 the two locations indicated in Figures 1 and 2.

Step 3: Remove the F-00011 SkyView Template.

Step 4: Final-Drill #19 the two #30 holes drilled in Step 2.

PAGE

REVISION:

DATE:

VAN'S AIRCRAFT, INC.

MATCH-DRILL #30

FINAL-DRILL #19

10/03/11

PAGE

42D-04 RV-12

REVISION:

DATE:

F-1202B

FIGURE 1:

MAKING THE BACKUP

BATTERY ATTACH HOLES

ISOMETRIC VIEW

CLECO HOLES

IN TEMPLATE

POINT AIMS
INBOARD

F-00011

MATCH-DRILL #30

FINAL-DRILL #19

FIGURE 2:

MAKING THE BACKUP

BATTERY ATTACH HOLES

TOP VIEW

F-00011

F-1202B

CLECO HOLES

IN TEMPLATE

POINT AIMS
INBOARD

Содержание RV-12



































Результаты поиска

Содержание RV-12

Отзывы:

Похожие инструкции для RV-12

Бренды по названию

Популярные бренды

Van's Aircraft RV-12, Руководство пользователя

Результаты поиска

Содержание RV-12

Отзывы:

Похожие инструкции для RV-12

Бренды по названию

Популярные бренды