Van's Aircraft RV-12 Скачать руководство пользователя страница 34

Страница: 34 / 34

PAGE

REVISION:

DATE:

VAN'S AIRCRAFT, INC.

04/11/12

42D-34 RV-12

REVISION:

DATE:

NOTE: This page summarizes the
optional installation of a AV GARMIN

X96 GPS. Since this series of GPS is no

longer in production this page has been

added for builder convenience only.

Step 1: Remove the backshell, heatshrink
and d-sub pins from the end of the

WH-RV12-296-496 GPS Wiring Harness

using the TOOL ICM INSERT/EXTRACT
D-Sub Tool. See Page 42-13.

Step 2: Find the short green shield wire
coming from the wires going to the 1/8 Inch

Audio Plug on the WH-RV12-296-496 GPS
Wiring Harness and cut off the pin.

Strip the end of this wire.

Step 3: Find the black wire coming from
the Garmin Power Data Cable Connector
on the WH-RV12-296-496 GPS Wiring

Harness.

Cut this wire two inches from the d-sub pin.

Strip both the cut wire with the d-sub pin
and the wire going to Garmin Power Data
Cable Connector.

Crimp the black wire with d-sub pin and the
shield wire from Step 2 into one end of a
splice as shown in Figure 1.

Crimp the black wire going to the Garmin

Power Data Cable Connector into the

other end of the splice.

Insert this wire into the ES-00140 9-Pin
Male D-Sub on the WH-00034 SkyView

GPS-250 Harness as shown in Figure 1.

Step 4: Cover the ends of the blue and
yellow wires coming from the Garmin

Power Data Cable Connector on the

WH-RV12-296-496 GPS Wiring Harness in

heat shrink.

Fold the blue and yellow wires back and

tie-wrap them to the GPS wiring harness.

Step 5: Insert the remaining wires coming

from the WH-RV12-296-496 GPS Wiring

Harness into the ES-00140 9-Pin Male
D-Sub on the WH-00034 SkyView
GPS-250 Harness as shown in Figure 1.

FIGURE 1: INSTALLING PINS

IN THE WH-00034

CONNECTOR

(REAR VIEW / PIN INSERTION SIDE)

WH-00034

GARMIN POWER DATA CABLE CONNECTOR

COVER ENDS IN HEAT SHRINK

SV-GPS-250

AV GROUND LOOP

1/8 INCH AUDIO PLUG

ES 320559

ES-00140

AV GARMIN X96 GPS

RED

BLU

Содержание RV-12



































Результаты поиска

Содержание RV-12

Отзывы:

Бренды по названию

Популярные бренды

Van's Aircraft RV-12, Руководство пользователя

Результаты поиска

Содержание RV-12

Отзывы:

Бренды по названию

Популярные бренды