background image

www.vanco1.com

 800-626-6445

2

1.  Do not expose this unit to water, moisture, 

or excessive humidity.

2.  Do not install or place this unit in a built-in 

cabinet, or other confined space without 
adequate ventilation.

3.  To prevent risk of electrical shock or fire 

hazard, due to overheating, do not obstruct 
unit’s ventilation openings.

4.  Do not install near any source of heat, 

including other units that may produce heat.

5.  Do not place unit near flames.

6.  Only clean unit with a dry cloth.
7.  Unplug unit during lightening storms, or 

when not used for an extended period 
of time. A surge protector is strongly 
recommended.

8.  Protect the power cord from being walked 

on or pinched, particularly at the plugs.

9.  Use unit only with accessories specified by 

the manufacturer.

10. Refer all servicing to qualified personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same 
video resolution and audio settings on all electronic equipment in the system. When there are multiple 
sources and displays, the video resolution and audio setting on all connected units must be adjusted 
to correspond with that of the display having the lowest video and audio capability. 

WARNING

DEAR CUSTOMER 

Thank you for purchasing this product.  
For optimum performance and safety, please  
read these instructions carefully before 
connecting, operating or adjusting this product. 
Please keep this manual for future reference.

This product is 100% inspected and tested in the United States 

to verify HDMI performance parameters.

Содержание HDWIR-RX













Отзывы: