background image

www.vanco1.com

800.626.6445

2

1.  Do not expose this unit to water, moisture, or 

excessive humidity.

2.  Do not install or place this unit in a built-in 

cabinet, or other confined space without 
adequate ventilation.

3.  To prevent risk of electrical shock or fire 

hazard, due to overheating do not obstruct 
unit’s ventilation openings.

4.  Do not install near any source of heat, 

including other units that may produce heat.

5.  Do not place unit near flames.
6.  Only clean unit with a dry cloth.

7.  Unplug unit during lightening storms or when 

not used for an extended period of time. A 
surge protector is strongly recommended.

8.  Protect the power cord from being walked on 

or pinched, particularly at the plugs.

9.  Use unit only with accessories specified by 

the manufacturer.

10. Refer all servicing to qualified personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same 
video resolution and audio settings on all electronic equipment in the system. When there are multiple 
sources and displays, the video resolution and audio setting on all connected units must be adjusted 
to correspond with that of the display having the lowest video and audio capability.

WARNING

DEAR CUSTOMER 

Thank you for purchasing this product.  

For optimum performance and safety, please  

read these instructions carefully before connecting, operating or 

adjusting this product. Please keep this manual for future reference.

This product is 100% inspected and tested in the United States to verify 

HDMI performance parameters.

Содержание EVWP2006RX













Отзывы: