VAMP 260 Скачать руководство пользователя страница 27

Страница: 27 / 78

VAMP Ltd

Power monitoring unit

Operation and configuration

VAMP 260

VM260.EN004

Vamp 24h support phone : +358 (0)20 753 3264

5.8.

Protocol menu Bus

Via the submenus of the protocol menu the following functions

can be read and set:

PROTOCOL

•

Communication protocol of REMOTE port (Protoco)

•

Message counter (Msg#)

•

Communication error counter (Errors)

•

Communication time-out counter (Tout)

MODBUS

•

Device slave number at Modbus Slave Protocol or

Target slave number at Modbus Master Protocol (Addr)

•

Modbus transfer rate (bit/s)

•

ModBus parity check (Parity)

SPABUS SLAVE

•

Slave number (Addr) when unit connected to SPA-Bus

•

SPA-Bus transfer rate (bit/s)

•

Event mode (Emode)

ProfiBus DP

•

ProfiBus profile (Mode)

•

Transfer rate of converter (bit/s)

•

ProfiBus Tx Buf length (InBuf)

•

ProfiBus Rx Buf length (OutBuf)

•

ProfiBus address (addr)

•

Type of the ProfiBus converter (conv)

IEC-60870-5-103

•

Slave address (Addr)

•

Transfer rate (bit/s)

TCP/IP (Only in VAMPSET)

•

IP address of the unit (IpAddr)

•

Subnet mask (NetMsk)

•

IP address of the Gateway (Gatew)

•

IP address of the Name Server (NameSv)

•

IP address of the SNTP Server (NTPSvr)

•

IP port number for protocol (Port)

Содержание 260















































































Результаты поиска

Содержание 260

Отзывы:

Похожие инструкции для 260

Бренды по названию

Популярные бренды

VAMP 260, Инструкции по эксплуатации и настройке

Результаты поиска

Содержание 260

Отзывы:

Похожие инструкции для 260

Бренды по названию

Популярные бренды