Valor Adorn 640 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 53

Valor Adorn 640 Скачать руководство пользователя страница 46

INSTALLER’S GUIDE

Page 46

Figure 64. Thermocouple interrupter block

apply tension to the microswitch leads.

7.

Remove the two fixing screws that

attach the generator unit to the support
bracket. The igniter generator can now
be removed. (see figure 63)

8.

Remove the two leads to the switch

and remove the spark lead. If
necessary, mark them to ensure that
they are replaced on to the correct
terminals.

9.

Replace the generator

10.

Refit in the reverse order.

16.9

To Remove the Thermocouple

Interrupter Block

See figure 64.

1.

Remove the bottom front and fire

front castings and the front surround -
See section 16.3.

2.

Detach the thermocouple from the

interrupter block by unscrewing the
thermocouple nut.

3.

Detach the two microswitch leads

from the interrupter block.

4.

Remove the interrupter block by

unscrewing from the gas
shut-off tap.

5.

Refit in the reverse

order. If the microswitch
leads cannot be easily
attached to the interrupter
block when it is fully
tightened to the gas shut-
off tap, slacken it and
rotate to allow the leads to
be fitted. Retighten making
sure that the leads remain
in place in the interrupter
block. Fit and tighten the

Figure 63. Removal of Electronic
Generator.

«
...
44
45
46
47
48
...
»

Содержание Adorn 640






















































Отзывы:

Нет отзывов