Valley VRI-iS Скачать руководство пользователя

Страница: 15 / 102

Installation Instructions

Install Slip Ring (Continued)

14. Attach the mounting brackets to ring stack. Use

the applicable instructions below based on the
type of collector ring.

• Aeromotive

ring stack - see Figure 15-1.

(a) Remove any three of the four #8 screws

that are securing the top ring. These would
have already been removed if a resolver
was removed.

(b)

Locate three mounting brackets that
DO NOT have an ID hole near one end.
This bracket is only for the Aeromotive
collector ring.

one #10 x 3/4 in screw in the hole and se-
cure with one #10 hex nut. Repeat for the
other two mounting brackets. See Figure
15-1.

(d) Secure each mounting bracket to the ring

stack with one 1/4 in flat washer and one
#8 screw.

(e) Align holes in slip ring board with #10

screws on mounting brackets. Secure slip
ring with three #10 lock washers and hex
nuts.

• Insul-8

ring stack - see Figure 15-2.

(a) Remove the top hex nut and lock washer

from each bolt securing the ring stack.
These would have already been removed
if a resolver was removed.

(b)

Locate three mounting brackets that
have an ID hole near one end. This
bracket is only for the Insul-8 collector
ring.

does not

have the ID hole, install one #10

x 3/4 in screw in the hole and secure with
one #10 hex nut. Repeat for the other two
mounting brackets. See Figure 15-2.

(d) Secure each mounting bracket to a ring

stack bolt with one #8 hex nut and lock
washer.

(e) Align holes in slip ring board with #10

screws on mounting brackets. Secure slip
ring with three #10 lock washers and hex
nuts.

Figure 15-1 Aeromotive Collector Ring

1.  #10 x 3/4 Screw
2.  Mounting Bracket
3.  #10 Hex Nut
4.  #8 Screw
5.  Ring

6.  1/4 Flat Washer
7.  Slip Ring Board
8.  #10 Lock Washer
9.  #10 Hex Nut
10. No ID Hole

Figure 15-2 Insul-8 Collector Ring

1.  #10 x 3/4 Screw
2.  Mounting Bracket
3.  #10 Hex Nut
4.  #8 Hex Nut
5.  Ring Stack

6.  #8 Lock Washer
7.  Slip Ring Board
8.  #10 Lock Washer
9.  #10 Hex Nut
10. ID Hole

Содержание VRI-iS







































































































Результаты поиска

Содержание VRI-iS

Отзывы:

Похожие инструкции для VRI-iS

Бренды по названию

Популярные бренды

Valley VRI-iS, Руководство по установке

Результаты поиска

Содержание VRI-iS

Отзывы:

Похожие инструкции для VRI-iS

Бренды по названию

Популярные бренды