manualshive.com logo in svg

Valcom PagePac Plus V-5323100, Руководство пользователя

Поделиться
Скачать
Valcom PagePac Plus V-5323100 Скачать руководство пользователя страница 15

15

947180

Hear TRIPLE beeps.

3. To verify the condition (OFF/ON) of the Dial Tone Detect option, dial 

2 5

 and repeat step 2 above.

3 0   SET CONNECT PASSWORD

This feature will not become active until the first time you enter a password, via the programming mode. 
The factory default is NO password. The Connect password operates as a security block into the paging 
system, restricting paging access to authorized users.

Note:

 You may want to use a short Connect password (2 or 3 digits only) for ease of use.

1. Dial 

3 0

 to select this option.

Hear a DOUBLE beep.

2. Enter the Password you wish to use (up to 6 digits). If the password has fewer than 6 digits, enter the

#

 to terminate the string. 

Note:

 For example, 123456 is a valid password entry. 123# is also a valid password entry, resulting in 

the password 123.

If you already have entered a password and want to remove it (to have NO password), just enter the # 
alone. Hear TRIPLE beeps.

To verify that the new Connect password has been established, dial 

3 1

 and repeat step 2 above.

3 2   SET PROGRAMMING PASSWORD

Establishing a Programming password will restrict access to the programming mode of the PagePac 
Plus paging system. It is recommended that access to programming be restricted to the System Admin-
istrator, Telecommunications Manager, or other selected users.

Note:

 Your Connect and Programming passwords should not be the same. If this feature is active and 

the system has been accessed via the telephone interface, then after the first digit of your Programming 
password is pressed, the dial tone will stop and will not be returned until the correct password is entered 
or until the user hangs up and re-enters the system.

This feature will become active once any programming password has been entered via the programming 
mode. You are not required to establish such a password. The factory-set default programming pass-

word is 

∗

 

∗

.

 
1. Dial 

3 2

 to select this option.

Hear a DOUBLE beep.

2. Enter the Password you wish to use (up to 6 digits). If the password has fewer than 6 digits, enter the

#

 to terminate the string.

If you already have entered a password and now want to remove it (to have NO password), just enter the 

#

 alone.

For example, 234567 is a valid password entry. 234# is also a valid password entry, resulting in the 
password 234.

Technical Manuals Online! - http://www.tech-man.com

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание PagePac Plus V-5323100















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды