Valach VM 120 B2-4T Скачать руководство пользователя

Страница: 4 / 24

Instructions Valach VM 120 B2-4T

Engine application

The VM 120 B2-4T is intended to be used in model airplanes. Other applications are

not permitted!

Description of the engine

The VM 120 B2-4T is a gasoline powered four-stroke flat twin engine, working on the

OHV principle with two valves per cylinder and petroil lubrication. The processor

controlled ignition makes starting a childs play and provides smooth running in all

RPM ranges.

Fuel

For fuel, use unleaded petrol with a minimum of 95 octane mixed with a full synthetic

two stroke oil.

We use and recommend

ARAL Ultimate 102

. It contains no bio-ethanol, the shelf life

of the mixture is much longer, the odor is reduced, the burning more gentle.

Attention with E10 Fuel: The shelf life is much shorter. Mixed fuel has to be used within

30 days!

The first two hours of the breaking-in time has do be done with a mixture with a ratio

of 1:25, this equates 4% oil in the gasoline. After that we recommend a mixture of

1:30. The whole breaking-in time is approx. three hours.

After many tests, the oil we recommend for the Valach Motors four

stroke engines is

Valvoline SynPower® 2T

The extremely high quality BelRay H1R, we use for our two-stroke

engines, is not ideal for petrol lubrication in four-stroke engines.

BelRay H1R burns off very well and deposit free, but it does not blow

down past the piston rings into the crankcase as well as

Valvoline

SynPower® 2T

. The design engineer does not recommend to use

Castrol oils, because they built up far too much carbon.

Do not use ready mixed synthetic odorless chain saw fuel. Use

the four-stroke version without oil and mix it with

Valvoline Syn-

Power® 2T

Breaking-in mixture:

5 Liter gasoline and 200 ml oil , this 5 Liter are enough for the breaking-in.

Mixture afterwards:
5 Liter gasoline and 170 ml oil, or per Liter gasoline 33 ml oil.

Содержание VM 120 B2-4T

























Результаты поиска

Содержание VM 120 B2-4T

Отзывы:

Похожие инструкции для VM 120 B2-4T

Бренды по названию

Популярные бренды

Valach VM 120 B2-4T, Инструкция по эксплуатации

Результаты поиска

Содержание VM 120 B2-4T

Отзывы:

Похожие инструкции для VM 120 B2-4T

Бренды по названию

Популярные бренды