manualshive.com logo in svg

Valach VM 120 B2-4T, Инструкция по эксплуатации

Поделиться
Скачать
Valach VM 120 B2-4T Скачать руководство пользователя страница 8

©2015  Toni Clark practical scale GmbH   Zeiss-Str.10   D-32312 Lübbecke   Tel. 0049 5741/5035   Fax. 05741/40338   www.toni-clark.com 

 Instructions   Valach VM 120 B2-4T  

8

Crankcase venting

The tube on the crankcase venting is used to remove the surplus oil out of the engine. 

Do not extend the tube or reduce the diameter.

Hint:

    I guide the rests of the oil into a plastic container, that is filled with absorbent cotton  

wads (from the dentist). The oil is absorbed by the cotton and will not come out while 

the wildest aerobatic maneuvers. I use an empty 100 ml bottle of our silver solder flux 

H1. The cap has a double sided tank nipple and eight 3 mm venting holes in it. 

Do not omit the venting holes, they are absolutely necessary! The small tube on the 

nipple guides the oil in the middle of the cotton in the bottle. I attached the container 

with Velcro into the model, so it can be easily removed for draining. 

The bottle must be placed lower then the crankcase vent!

Содержание VM 120 B2-4T

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды