VAL VLP-2430-4 Скачать руководство пользователя страница 5

Rev. 1.1 

6.Operation 

(1) Connections 

      Confirm the power switch is OFF (on “0” side). 

Connect the LED lighting unit to CH1 or CH2 or CH3 or CH4 output connector on front panel of the product. 
Connect 3P socket of the AC power cord to power supply inlet on front panel of the product 
and connect 3P plug of the AC power cord to outlet. 

CAUTION 

Connect an outlet with grounding. If it is not grounded, the power supply will not be ensured 
electrical safety performance. 

 
(2) Power on 

    Turn the power switch to ON (on “I” side). Set the intensity to minimum side to suppress the inrush current.  

 
(3) Manual control 

  Light intensity is adjustable manually when the control switch on the front panel is set at “INT.” 

   

(4) Remote control 

    When the Remote control switch on front panel is set at “EXT.”, external control input signal is available 

through “RS-232C”or “TRIG. IN” connector on front panel. 

 
  (5) On/Off Control 
      It is possible to turn off the light by inputting “off” signal by remote control mode. 
   

(6) Error Signal 

Error indicator on front panel will be on if an error of LED lighting unit detected such as breaking of wire. 
Error signal from external signal connector will be output at the same time.  
It does not identify error of CH1 or CH2 or CH3 or CH4. Please check the lighting units. 
This function does not detect the connection of lighting unit. To avoid signal malfunction, set the output minimum 
level if the lighting unit is not connected. 

This function works regardless of “INT./EXT.” mode. 

 
(7) Noise reduction 

Make sure to attach a 

Ferrite core clamp filter to AC power cord.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание VLP-2430-4











Отзывы: