Vaillant TURBOmax Pro 28/2 E Скачать руководство пользователя страница 22

Страница: 22 / 72

Supplied By www.heating spares.co Tel. 0161 620 6677

BOILER INSTALLATION SEQUENCE

Cold water mains inlet
and hot water outlet

Flush all foreign matter from the mains
supply before connecting to the
boiler.

●

Connect the cold water service
valve (

) to the cold inlet water

connection of the appliance with
the washer (

) provided and tigh-

ten.

●

Connect cold water service pipe to
the cold water service valve and
tighten.

●

Connect the 15 mm hot water
outlet copper tail (

) to the hot

water outlet connection of the
appliance with the washer (

) pro-

vided and tighten.

●

Connect hot water outlet pipework
to the copper tail.

Note: The hot water outlet union nut
is packed in with the PRV fittings
pack.

Euro B/S 045/0GB_Pro

Fig. I.7: Fitting the hot and cold water connections

Содержание TURBOmax Pro 28/2 E









































































Результаты поиска

Содержание TURBOmax Pro 28/2 E

Отзывы:

Похожие инструкции для TURBOmax Pro 28/2 E

Бренды по названию

Популярные бренды

Vaillant TURBOmax Pro 28/2 E, Инструкция по установке и обслуживанию

Результаты поиска

Содержание TURBOmax Pro 28/2 E

Отзывы:

Похожие инструкции для TURBOmax Pro 28/2 E

Бренды по названию

Популярные бренды