Vaillant ecoMAX pro SERIES Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 36

Vaillant ecoMAX pro SERIES Скачать руководство пользователя страница 25

Servicing 15

Instructions for Use, Installation and Servicing ecoMAX pro

25

15.3 Burner

Refer to Figs. 15.2, 15.3, 15.4 and 15.5.
Isolate the gas supply at the gas service cock.
Disconnect the gas supply at the union nut of the gas
service cock.

Note!
Do not disconnect at the gas valve.

Remove the two gas pipe bracket securing screws from
underside of inner case, see Fig. 15.2.
Drop down the control panel into the service position.
Remove the four screws from the chassis front, see Fig.
15.3.
Remove the chassis front by pulling it out at the top
from its retaining slots.

Note!
When replacing chassis front panel ensure the
bottom fits behind lip.

Disconnect the gas control valve plug at the gas control
valve, see Fig. 15.4.
Disconnect the electrical leads from the fan.
Remove the five combustion chamber front securing
nuts, see Fig. 15.5.

Fig. 15.2

Fig. 15.3

CONTROL
PANEL
SERVICE
POSITION

SECURING
SCREW
(4 OFF)

CHASSIS
FRONT

CONDENSE
TRAP

GAS SERVICE
COCK

GAS
SUPPLY PIPE IN

GAS PIPE BRACKET
SECURING SCREW

SEALING
GROMMET

UNION NUT

Fig. 15.4

Fig. 15.5

Gently remove the fan, gas control valve and burner
assembly from the combustion chamber complete with
the gas pipe bracket and seal.
Clean the burner with a soft brush taking great care not
to damage the front insulation. DO NOT use wire or
sharp instruments to clean the holes of the burner.
Inspect the burner for any signs of damage.
Removal of the burner from the fan, gas control valve
and burner assembly is not necessary during an annual
service.

BURNER

COMBUSTION
CHAMBER

FAN

GAS
CONTROL
VALVE

GAS PIPE
BRACKET
& SEAL

SECURING
NUTS (5
OFF)

GAS CONTROL
VALVE

FAN

COMBUSTION
CHAMBER FRONT
SECURING NUTS
(5 OFF)

HEAT EXCHANGER

IGNITION
LEAD

COMBUSTION
ANALYSER TEST
POINT

FLUE
ADAPTER

ELECTRODE
CONNECTOR

«
...
23
24
25
26
27
...
»

Содержание ecoMAX pro SERIES





































Отзывы:

Нет отзывов